Rockwell-automation 1560E SMC Flex Smart Motor Controller Manual de usuario Pagina 29
- Pagina / 198
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Product Overview 1-19
%5-"%.0*UNE
Status Indication Four programmable hard contact outputs are provided as standard:
• The Auxiliary #1 Contact is N.O. It is always programmed for
Up-to-speed to control the bypass contactor in MV applications.
• The fault Contact is for fault indication and is programmable for N.O./N.C.
• The alarm Contact is for alarm indication and is programmable for N.O./N.C.
• The Auxiliary #2 Contact is for normal indication and is programmable
for N.O./N.C. For MV applications, it is configured as N.O. to control
the line contactor.
11 12 13 14 15 16 17 18 19 20 21 22
SMC-Flex
Control Terminals
Aux#1
Up-to-Speed
23 24 25 26 27 28 29 30 31 32 33 34
PTC
Input
TACH
Input
Ground
Fault
Fault
Contact
Alarm
Contact
Aux #2
Normal
11 12 13 14 15 16 17 18 19 20 21 22
SMC-Flex
Control Terminals
Aux#1
Up-to-Speed
23 24 25 26 27 28 29 30 31 32 33 34
PTC
Input
TACH
Input
Ground
Fault
Fault
Contact
Alarm
Contact
Aux #2
Normal
Figure 1.16 – Control Terminals
Control Options The MV SMC-Flex™ controller offers the control options described below.
Important: The options listed in this section are mutually exclusive and
must be specified when ordering. An existing controller may be upgraded
to another control option by replacing the control module and possibly other
components. Consult your nearest Rockwell Automation sales office.
Pump Control Option
This option reduces surges during the starting and stopping of a centrifugal
pump by smoothly accelerating and decelerating the motor. The micro-
processor analyzes the motor variables and generates commands that control
the motor and reduce the possibility of surges occurring in the system.
The motor current will vary during the acceleration period, and may be
near the motor rated starting current. The pump algorithm does not limit
starting current since full voltage is needed to reach full speed with a
loaded motor.
The starting time is programmable from 0-30 seconds, and the stopping
time is programmable from 0-120 seconds.
- Medium Voltage 1
- SMC Flex™ 1
- Motor Controller 1
- Important User Information 2
- Table of Contents 3
- Installation Chapter 2 4
- Programming Chapter 4 5
- Metering Chapter 5 Page 6
- Options Chapter 6 6
- Diagnostics Chapter 7 6
- Communications Chapter 8 6
- Maintenance Chapter 10 7
- Appendix D Spare Parts 8
- Appendix E Accessories 8
- 1560E-UM050B-EN-P - June 2013 10
- Product Overview 11
- 1560E – Retrofit Controller 12
- SMC-Flex™ Control Module 12
- Figure 1.1– Soft Start 13
- Selectable Kickstart : 14
- Current Limit Start ; 14
- Dual Ramp Start : 15
- Full Voltage Start 15
- Preset Slow Speed 16
- Product Overview 1-7 17
- Soft Stop 18
- Overload 19
- Protection and Diagnostics 20
- Underload : 21
- Undervoltage ; 21
- Overvoltage ; 21
- Ground Fault 23
- Table 1.A –PTC Input Ratings 25
- Excessive Starts/Hour 27
- Overtemperature 27
- Figure 1.14 – DPI Location 28
- Pump Control Option 29
- 1-20 Product Overview 30
- Braking Control Option 31
- Power Module 32
- Interface Board 33
- 1-24 Product Overview 34
- Product Overview 1-25 35
- 1-26 Product Overview 36
- Product Overview 1-27 37
- 1-28 Product Overview 38
- 1-30 Product Overview 40
- Product Overview 1-31 41
- 1-32 Product Overview 42
- Product Overview 1-33 43
- Product Overview 1-35 45
- 1-36 Product Overview 46
- Product Overview 1-37 47
- 1-38 Product Overview 48
- Installation 49
- 2-2 Installation 50
- Mounting 51
- Grounding Practices 52
- (with LV panels not shown) 54
- Installation 2-7 55
- Installation 2-9 57
- Power Connections (cont.) 58
- Bulletin 1503E 59
- 2-12 Installation 60
- Installation 2-13 61
- 2-14 Installation 62
- Installation 2-15 63
- Surge Arrestor Protection 64
- Two-speed Motors 65
- Multi-motor Protection 65
- EMC Compliance 66
- Wire Size Torque 67
- 0.75 to 2.5 mm 67
- 2-20 Installation 68
- Commissioning Procedure 69
- System Characteristics 70
- MV SMC-Flex™ Module 71
- 3-4 Commissioning Procedures 72
- Commissioning Procedures 3-5 73
- 3-6 Commissioning Procedures 74
- Figure 3.3 – Interface PCB 75
- 3-8 Commissioning Procedures 76
- Milliseconds 77
- Control Function Tests 78
- Programming 81
- Programming Menu (cont.) 82
- Programming 4-3 83
- Table 4.A 84
- Parameter Linear List 84
- Programming 4-5 85
- EscEsc SelSel 86
- Using Parameter Management 87
- (Dual Ramp) 90
- Parameter Option 91
- Starting Mode 91
- Full Voltage 91
- Basic Setup (cont.) 92
- Undervoltage u 94
- Overvoltage u 94
- Underload v 94
- Motor Data Entry 95
- 4-16 Programming 96
- Metering 97
- Viewing Metering Data 98
- Human Interface Module 100
- Programming Parameters 102
- Options 6-5 103
- 6-6 Options 104
- Diagnostics 105
- 7-2 Diagnostics 106
- Table 7.A 107
- Fault Code Cross-Reference 107
- 7-4 Diagnostics 108
- Communications 109
- Keypad Description 110
- Communications 8-3 111
- Control Enable 112
- Communications 8-5 113
- Loss of Communication and 114
- Network Faults 114
- Table 8.E 115
- SMC-Flex Bit Identification 116
- Scale Factors for PLC 117
- Communication 117
- Rules for Using DataLinks 118
- Troubleshooting 119
- : Prestart fault indication 121
- Troubleshooting 9-5 123
- 9-6 Troubleshooting 124
- Voltage Feedback Circuit 125
- Voltage-Sensing Board 126
- Replacement 126
- Figure 9.3 – IGDPS Board 127
- 9-10 Troubleshooting 128
- Troubleshooting 9-11 129
- SCR Replacement Procedure 131
- Power Circuit 132
- Troubleshooting (cont.) 132
- Troubleshooting 9-15 133
- Troubleshooting 9-17 135
- Figure 9.6 – Heatsink Clamp 136
- Troubleshooting 9-19 137
- Figure 9.9 – Heatsink Clamp 138
- Troubleshooting 9-21 139
- Troubleshooting 9-23 141
- 9-24 Troubleshooting 142
- Troubleshooting 9-25 143
- Snubber and Resistor Circuit 145
- VOLTAGE FEEDBACK 146
- Troubleshooting 9-29 147
- 9-30 Troubleshooting 148
- Troubleshooting 9-31 149
- 9-32 Troubleshooting 150
- Troubleshooting 9-33 151
- 9-34 Troubleshooting 152
- Troubleshooting 9-35 153
- 9-36 Troubleshooting 154
- Troubleshooting 9-37 155
- 9-38 Troubleshooting 156
- Troubleshooting 9-39 157
- 9-40 Troubleshooting 158
- Maintenance 159
- Vacuum Bottles 160
- Terminals 160
- Solid-State Devices 161
- Static-Sensitive Items 161
- Final Check Out 161
- 10-4 Maintenance 162
- Environmental Considerations 163
- Appendix A 165
- A-2 Specifications 166
- Bulletin 1560E 169
- Bulletin 1562E 169
- Description Specifications 170
- Description 172
- Parameter Information 173
- Parameter Information B-3 175
- B-4 Parameter Information 176
- 1560E and 1562E Relay Control 177
- SMC-Flex module 178
- Spare Parts 187
- Table D.2 188
- Spare Parts D-3 189
- Table D.4 190
- Table D.6 192
- Table D.7 193
- Accessories 194
- Table D.8 194
- E-2 Accessories 196
Relacionado con productos y manuales para Equipo Rockwell-automation 1560E SMC Flex Smart Motor Controller
Equipo Rockwell-automation 1606-XLP60BQT Power Supply Reference Manual Manual de usuario
(24 paginas)
(24 paginas)
(42 paginas)
Equipo Rockwell-automation 1492-AIFMQS 4 Input / 4 Output Fusible Analog Inte Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 1492-CM800-LD009 Field Wire Conv. Module for Modic Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 1492-IFM20DS24-4_IFM20DS120-4 8 Point Isolated Int Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1512A MV Controllers - 800A One-High Cabinet Manual de usuario
(105 paginas)
(105 paginas)
Equipo Rockwell-automation 1492-XIMTRxxx_RXIMTRxxx 16 and 32 Point Relay Inte Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 1585BP Bulkhead Coupler Installation Instructions Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1492-CM1771-LD001 Digital I/O Conversion Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1102C-PKxx 400A / 600A Vacuum Contactor AC Coil Re Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1336T Function Block Prog. Manual, Series A/B Manual de usuario
(180 paginas)
(180 paginas)
(43 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales