Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D Manual de usuario Pagina 88
- Pagina / 98
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
88 Rockwell Automation Publication 6000-IN007A-EN-P - October 2014
Appendix C Special Function Parameter Settings
Switch Control Sources
Relevant parameter: P4
Description: P4 selects the control source to start, stop, or reset the drive.
There are two Control Sources, the HMI and the hard-wired I/O interface
(DCS). They cannot be enabled at the same time.
Rated/Maximum Output Frequency
Relevant parameter: P460, P466
Description: sets the rated output frequency.
Instruction: P460 is drive’s rated output frequency, which should be the same as
the motor’s rated frequency (0…75 Hz). P466 is the drive’s Maximum Output
Frequency; P460 cannot exceed P466.
Motor Parameter Setting
Relevant parameter: P17, P199
Description: set basic motor parameters, such as rated current and the number of
pole pairs.
Instruction: P199 is motor rated current, which is used to determine faults. P17
sets the number of motor pole pairs.
Hall Effect Current Sensor Setting
Relevant parameter: P198
Instruction: Set the HECS rated current (A) used for the drive current sampling.
- Commissioning Manual 1
- Important User Information 2
- Table of Contents 3
- Table 1 - Electrical Drawings 7
- General Precautions 9
- Additional Resources 9
- Introduction 11
- Documentation and 12
- Application Review 12
- Review Drive Application 13
- Chapter 1 Introduction 14
- Preparation and Inspection 15
- Inspect Drive Components 16
- Functional Assessment 17
- Interconnection Review 20
- Installation Review 21
- Power Cabling 22
- Drive Megger Check 23
- Figure 4 - Control Switches 25
- Figure 5 - Control Switches 25
- Figure 8 - Back of HMI 26
- Connect the Insulation Meter 27
- Final Steps before 29
- Equipment is Ready for 29
- Energization 29
- Commissioning 31
- Control System Check Setup 32
- Control System Check 35
- , press 36
- Access Setup Settings 37
- Set P Parameters 38
- Commissioning Chapter 3 39
- Chapter 3 Commissioning 40
- Increase Frequency by Step 41
- Simulate Warnings and Faults 45
- Verify E-Stop Functionality 50
- (Manual Bypass) 52
- Bypass Isolation Switches 54
- (Automatic Bypass) 55
- , and press 57
- Bypass Contactors 58
- Figure 17 - Status Indicators 61
- Table 9 - Drive to DCS 61
- Table 10 - 4-20 mA 61
- Restore P Parameter Settings 62
- Set Date and Time Zone 64
- No-load Test 67
- Configure P and T Parameters 68
- 0 ON -100 199.99 R&D 69
- (2) With Remote DCS only 70
- Parameters T11...T13 71
- Chapter 4 No-load Test 72
- Change Parameter T12: 73
- 3. Press to accept 73
- Close Input Circuit Breaker 75
- Check Cooling Fan Operation 75
- Operate Motor by HMI 76
- No-load Test Chapter 4 77
- Press to confirm 78
- Load Test of Drive System 80
- Torque Requirements 81
- Single Line Diagrams 83
- Appendix C 87
- Overview 87
- System Setting Functions 87
- Switch Control Sources 88
- Motor Parameter Setting 88
- Restore Factory Setting 89
- Speed Command Functions 90
- Frequency Amplitude Limit 91
- Frequency Skip 91
- Speed Reference Functions 92
- Analog Input 93
- Stop Mode 93
- Flying Start Function 93
- Restart the Drive 94
- Rockwell Automation Support 98
- Documentation Feedback 98
Relacionado con productos y manuales para Equipo Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D
Equipo Rockwell-automation 2711PC-xxxx PanelView Plus 6 Compact Terminals Use Manual de usuario
(162 paginas)
(162 paginas)
Equipo Rockwell-automation 6181P_F VersaView 6181P Integrated Display Compute Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 2090-XBxxx Resistive Brake Module Installation Ins Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 2364F Regenerative DC Bus Supply Unit (RGU) Manual de usuario
(222 paginas)
(222 paginas)
Equipo Rockwell-automation 2090-CSWMxxx Single Motor Cables with Circular DIN Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2090-CBUSPSS Kinetix 6000M Bulkhead Cable Adapter Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 2090-CSBM1DF-10AF Single Motor Cables with Circula Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 2080 Micro800 Digital and Analog Plug-in Modules Manual de usuario
(108 paginas)
(108 paginas)
Equipo Rockwell-automation MV SMC Flex OEM Components - Fiber Optic Cables Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 2094-EN02D-M01-S0 Kinetix 6200 and Kinetix 6500 Sa Manual de usuario
(42 paginas)
(42 paginas)
(52 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales