Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC Manual de usuario Pagina 154
- Pagina / 168
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
E-6
DeviceNet Adapter for use with DPI AC Drives
E.2 M-S Output Parameter Configurations
M-S Output (26) has five configurable bits as shown in figure E.2.
When you enable
Cmd/Ref
or
Datalink
in the adapter, you must set
the corresponding bit in M-S Output (26) if you want the output data
to be sent to the scanner or master device.
Tables E.3 and E.4 list possible configurations for M-S Output (26)
and the possible data size allocation associated with each value
depending on the method of data transfer.
Figure E.2 – Bits and Corresponding I/O
Table E.3 – Host Products using 16-bit Reference/Feedback and
Datalinks
M-S
Input
M-S
Output
Allocation (Number of Bytes)
Data Size sent from the Adapter to the
Controller
Poll
Only
COS
Only
Cyclic
Only
Poll &
COS
Poll &
Cyclic
xxxxx 00000 0 NA NA NA NA
xxxxx 00010 4 NA NA NA NA
xxxxx 00100 4 NA NA NA NA
xxxxx 00110 8 NA NA NA NA
xxxxx 01000 4 NA NA NA NA
xxxxx 01010 8 NA NA NA NA
xxxxx 01100 8 NA NA NA NA
xxxxx 11100 12 NA NA NA NA
xxxxx 10000 4 NA NA NA NA
xxxxx 10010 8 NA NA NA NA
xxxxx 10100 8 NA NA NA NA
xxxxx 10110 12 NA NA NA NA
xxxxx 11000 8 NA NA NA NA
xxxxx 11010 12 NA NA NA NA
xxxxx 11100 12 NA NA NA NA
xxx0, 0000
Datalink D
Datalink C
Datalink B
Datalink A
Cmd/Ref
0 = Peer or other output
1 = Master-Slave output
- DeviceNet Adapter 1
- DPI AC Drives 1
- Contents 3
- List of Figures 7
- List of Tables 9
- Introduction 11
- 1.2 Related Documentation 12
- Electric 13
- Getting Started 15
- 2.2 Required Equipment 16
- 2.3 Installation Checklist 17
- Step Action Refer to 18
- Installing the 19
- 3.5 Applying Power 23
- Configuring the 25
- SP600 Standard 31
- 4.5 Setting the Data Rate 32
- Peer-to-Peer 33
- 4.9 Setting a Fault Action 41
- 4.10 Resetting the Adapter 43
- 00010xxx 45
- 01234567 45
- 1=Enabled 45
- 0=Disabled 45
- Configuring the Scanner 47
- AC Drive 48
- Edit I/O 49
- Parameters 49
- 5.4) appears 49
- 5.3.1 Mapping the Input I/O 52
- 5.3.2 Mapping the Output I/O 53
- 5.4 Saving the Configuration 54
- Using I/O Messaging 55
- 6.4 Using Reference/Feedback 58
- 6.5 Using Datalinks 58
- Using Explicit 67
- Messaging 67
- ControlLogix Controller 68
- Using Explicit Messaging 69
- PLC or SLC Controller 70
- Word Description 71
- 7.4 Running Explicit Messages 73
- 7.5 ControlLogix Example 74
- 7.6 PLC-5 Example 76
- Ladder Logic Program 77
- 7.7 SLC Example 78
- Troubleshooting the 81
- and Network 81
- 8.1.1 DRIVE Status Indicator 82
- 8.1.2 MS Status Indicator 83
- 8.1.3 NET A Status Indicator 84
- 8.2 Adapter Diagnostic Items 85
- Technical 91
- Specifications 91
- 1DPI Port 94
- 2 DPI Data Rate 94
- 3 DN Addr Cfg 94
- 4 DN Addr Actual 94
- 5 DN Rate Cfg 95
- 6 DN Rate Actual 95
- 7 Ref/Fdbk Size 95
- 8 Datalink Size 95
- 9 Reset Module 96
- 10 Comm Flt Action 96
- 11 Idle Flt Action 97
- 12 DN Active Cfg 97
- 13 DPI I/O Config 98
- 14 DPI I/O Active 98
- 15 Flt Cfg Logic 99
- 16 Flt Cfg Ref 99
- Figure B.3 – M-S Input (25) 100
- 26 M-S Output 101
- 27 COS Status Mask 101
- 28 COS Fdbk Change 101
- 29 COS/Cyc Interval 102
- Peer A Input 102
- Peer B Input 102
- 32 Peer Cmd Mask 103
- 33 Peer Ref Adjust 103
- 34 Peer Flt Action 104
- 35 Peer Node to Inp 104
- 36 Peer Inp Timeout 105
- 37 Peer Inp Enable 105
- 38 Peer Inp Status 105
- 43 Peer Out Skip 107
- DeviceNet 109
- C.1 Identity Object 110
- Services 111
- C.2 Connection Object 112
- C.3 Register Object 114
- Instance Attributes 115
- C.4 Parameter Object 116
- C.5 Parameter Group Object 119
- C.6 PCCC Object 121
- C.7 DPI Device Object 123
- C.8 DPI Parameter Object 127
- DeviceNet Objects 129
- Descriptor Attributes 130
- Decimal Places 131
- Decimal Place) 131
- C.9 DPI Fault Object 137
- C.10 DPI Alarm Object 140
- C.11 DPI Time Object 142
- Logic Command/ 145
- Status Words 145
- Logic Status Word 146
- Logic Command/Status Words 147
- Master-Slave 149
- I/O Configuration 149
- Datalinks 152
- Datalinks (Continued) 153
- Datalinks (Continued) 155
- Datalinks 156
- Glossary-1 157
- Glossary-2 158
- Glossary-3 159
- Glossary-4 160
- Glossary-5 161
- Glossary-6 162
Relacionado con productos y manuales para Equipo Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC
Equipo Rockwell-automation RECOMM-485 RS485 DFI Communications Module Manual de usuario
(68 paginas)
(68 paginas)
Equipo Rockwell-automation FactoryTalk Historian SE 3.0 H2H Interface Install Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation 20D PowerFlex 700S/700H Frame 10...14 Drives Maint Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation T8292 Trusted Power Distribution Unit MCB 24V Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation Logix5000 Control Systems: Connect POINT I/O Modul Manual de usuario
(62 paginas)
(62 paginas)
Equipo Rockwell-automation 1203-USB USB Converter (Same as DRIVES-UM001) Out Manual de usuario
(76 paginas)
(76 paginas)
Equipo Rockwell-automation SP200 AC Drive, 1 2 Channel Analog, Preset Speed Manual de usuario
(68 paginas)
(68 paginas)
(4 paginas)
Equipo Rockwell-automation GV3000/SE Operator Interface Module (OIM) User Gui Manual de usuario
(112 paginas)
(112 paginas)
Equipo Rockwell-automation FlexPak/WebPak 3000 DC Drive AutoMax Network Commu Manual de usuario
(108 paginas)
(108 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales