Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC Manual de usuario Pagina 63
- Pagina / 168
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using I/O Messaging
6-9
6.6.2 Sample PLC-5 Ladder Logic Program
Table 6.2 – Control File for Block Transfers
EN ST DN ER CO EW NR TO RW RLEN DLEN FILE ELEM R G S
BT20:0000000000 62 0 9 0 0000
BT20:1000000000 62 0 10 0 0000
Figure 6.5 – Sample PLC-5 Ladder Logic Program
0000
BT20:0
EN
EN
DN
ER
BTR
Block Transfer Read
Module Type Generic Block Transfer
Rack 000
Group 0
Module 0
Control Block BT20:0
Data File N9:0
Length 62
Continuous No
0001
N9:1
1
SP600
RUNNING
Status Bit
O:000
10
Operator Display
Drive Running
Status Bit
0002
N9:1
7
SP600
FAULTED
Status Bit
O:000
11
Operator Display
Drive Faulted
Status Bit
0003
MO
Move
Source N9:2
0<
Dest N21:1
0<
MOV
Operator Display
Drive Feedback
Status Word
0004
N10:0
0
1771-SDN Scanner
Port A Enable
0005
I:000
10
Operator Input
Drive Start
Command Bit
N10:1
1
SP600
START
Command Bit
The scanner gathers drive data via the DeviceNet network. The Block Transfer Read
in this rung then moves the drive status data from the scanner to the N9 data file in the
PLC.
These rungs move the drive status
from the Block Transfer Read data
to an operator display.
This rung enables the scanner.
These rungs move the inputs of the
operator station to the Block Transfer Write
data file. They will then be sent to the
scanner and out to the drive via the
DeviceNet network.
- DeviceNet Adapter 1
- DPI AC Drives 1
- Contents 3
- List of Figures 7
- List of Tables 9
- Introduction 11
- 1.2 Related Documentation 12
- Electric 13
- Getting Started 15
- 2.2 Required Equipment 16
- 2.3 Installation Checklist 17
- Step Action Refer to 18
- Installing the 19
- 3.5 Applying Power 23
- Configuring the 25
- SP600 Standard 31
- 4.5 Setting the Data Rate 32
- Peer-to-Peer 33
- 4.9 Setting a Fault Action 41
- 4.10 Resetting the Adapter 43
- 00010xxx 45
- 01234567 45
- 1=Enabled 45
- 0=Disabled 45
- Configuring the Scanner 47
- AC Drive 48
- Edit I/O 49
- Parameters 49
- 5.4) appears 49
- 5.3.1 Mapping the Input I/O 52
- 5.3.2 Mapping the Output I/O 53
- 5.4 Saving the Configuration 54
- Using I/O Messaging 55
- 6.4 Using Reference/Feedback 58
- 6.5 Using Datalinks 58
- Using Explicit 67
- Messaging 67
- ControlLogix Controller 68
- Using Explicit Messaging 69
- PLC or SLC Controller 70
- Word Description 71
- 7.4 Running Explicit Messages 73
- 7.5 ControlLogix Example 74
- 7.6 PLC-5 Example 76
- Ladder Logic Program 77
- 7.7 SLC Example 78
- Troubleshooting the 81
- and Network 81
- 8.1.1 DRIVE Status Indicator 82
- 8.1.2 MS Status Indicator 83
- 8.1.3 NET A Status Indicator 84
- 8.2 Adapter Diagnostic Items 85
- Technical 91
- Specifications 91
- 1DPI Port 94
- 2 DPI Data Rate 94
- 3 DN Addr Cfg 94
- 4 DN Addr Actual 94
- 5 DN Rate Cfg 95
- 6 DN Rate Actual 95
- 7 Ref/Fdbk Size 95
- 8 Datalink Size 95
- 9 Reset Module 96
- 10 Comm Flt Action 96
- 11 Idle Flt Action 97
- 12 DN Active Cfg 97
- 13 DPI I/O Config 98
- 14 DPI I/O Active 98
- 15 Flt Cfg Logic 99
- 16 Flt Cfg Ref 99
- Figure B.3 – M-S Input (25) 100
- 26 M-S Output 101
- 27 COS Status Mask 101
- 28 COS Fdbk Change 101
- 29 COS/Cyc Interval 102
- Peer A Input 102
- Peer B Input 102
- 32 Peer Cmd Mask 103
- 33 Peer Ref Adjust 103
- 34 Peer Flt Action 104
- 35 Peer Node to Inp 104
- 36 Peer Inp Timeout 105
- 37 Peer Inp Enable 105
- 38 Peer Inp Status 105
- 43 Peer Out Skip 107
- DeviceNet 109
- C.1 Identity Object 110
- Services 111
- C.2 Connection Object 112
- C.3 Register Object 114
- Instance Attributes 115
- C.4 Parameter Object 116
- C.5 Parameter Group Object 119
- C.6 PCCC Object 121
- C.7 DPI Device Object 123
- C.8 DPI Parameter Object 127
- DeviceNet Objects 129
- Descriptor Attributes 130
- Decimal Places 131
- Decimal Place) 131
- C.9 DPI Fault Object 137
- C.10 DPI Alarm Object 140
- C.11 DPI Time Object 142
- Logic Command/ 145
- Status Words 145
- Logic Status Word 146
- Logic Command/Status Words 147
- Master-Slave 149
- I/O Configuration 149
- Datalinks 152
- Datalinks (Continued) 153
- Datalinks (Continued) 155
- Datalinks 156
- Glossary-1 157
- Glossary-2 158
- Glossary-3 159
- Glossary-4 160
- Glossary-5 161
- Glossary-6 162
Relacionado con productos y manuales para Equipo Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC
Equipo Rockwell-automation RECOMM-485 RS485 DFI Communications Module Manual de usuario
(68 paginas)
(68 paginas)
Equipo Rockwell-automation FactoryTalk Historian SE 3.0 H2H Interface Install Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation 20D PowerFlex 700S/700H Frame 10...14 Drives Maint Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation T8292 Trusted Power Distribution Unit MCB 24V Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation Logix5000 Control Systems: Connect POINT I/O Modul Manual de usuario
(62 paginas)
(62 paginas)
Equipo Rockwell-automation 1203-USB USB Converter (Same as DRIVES-UM001) Out Manual de usuario
(76 paginas)
(76 paginas)
Equipo Rockwell-automation SP200 AC Drive, 1 2 Channel Analog, Preset Speed Manual de usuario
(68 paginas)
(68 paginas)
(4 paginas)
Equipo Rockwell-automation GV3000/SE Operator Interface Module (OIM) User Gui Manual de usuario
(112 paginas)
(112 paginas)
Equipo Rockwell-automation FlexPak/WebPak 3000 DC Drive AutoMax Network Commu Manual de usuario
(108 paginas)
(108 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales