Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O Manual de usuario Pagina 18
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
10 Rockwell Automation Publication 1734-UM017B-EN-P - October 2013
Chapter 2 Install Your POINT I/O or ArmorPOINT I/O Adapter
Mount the POINT I/O Adapter on a DIN Rail
1. Make sure the DIN rail locking screw (orange) is in horizontal position.
2. Position the adapter vertically above an IEC standard (35 x 7.5 x 1 mm)
top-hat DIN rail at a slight angle (DIN rail: Allen-Bradley part number
199-DR1; 46277-3).
3. Press down firmly to install the adapter on the DIN rail, noting that the
locking mechanism locks the adapter to the DIN rail.
4. Set the network address thumbwheel switches to the desired value. See Set
the Network Address in chapter3 for details on setting the IP address.
5. Slide the safety end cap up to remove it, exposing the backplane and power
interconnections.
ATTENTION: Allow 25.4 mm (1.0 in.) of space between adjacent
equipment for adequate ventilation.
ATTENTION: Do not discard the end cap. Use this end cap to cover the
exposed interconnections on the last mounting base on the DIN rail.
Failure to do so could result in equipment damage or injury from electric
shock.
ATTENTION: This product is grounded through the DIN rail to chassis
ground. Use zinc plated yellow-chromate steel DIN rail to assure proper
grounding. The use of other DIN rail materials (for example, aluminum or
plastic) that can corrode, oxidize, or are poor conductors, can result in
improper or intermittent grounding. Secure DIN rail to mounting surface
approximately every 200 mm (7.8 in.) and use end-anchors appropriately.
1734-AENTR Series B
Module
Status
Network
Activity
Network
Status
Point Bus
Status
Sys
tem
Powe
r
Field
Pow
e
r
POINT I O
75.30
(2.96)
74.00
(2.91)
132.72
(5.23)
52.23
(2.06)
35.55
(1.40)
A
B
45174
A = DIN rail
B = Secure DIN rail approximately every 200 mm (7.8 in.)
- EtherNet/IP Adapters 1
- Important User Information 2
- Who Should Use this 3
- Purpose of this Manual 3
- Common Techniques Used 4
- Table of Contents 5
- Adapter Features 9
- What the Adapter Does 10
- Physical Features of Your 11
- Adapters 11
- software releases 12
- chassis size 12
- Replacement 13
- Use of the Common 14
- Industrial Protocol (CIP) 14
- Chapter Summary 16
- Overview 17
- A = DIN rail 18
- Install POINT I/O Modules 19
- Remove POINT I/O Modules 19
- Remove ArmorPoint I/O Modules 22
- Replace An Adapter 23
- Wire the Adapter 24
- for more information 26
- third party DHCP server 27
- Configuration 28
- Requirements 28
- Gateway Address 29
- Subnet Mask 30
- Network Address 31
- Use the Rockwell BootP/ 32
- DHCP Utility 32
- 1. Run the BootP software 33
- Save the Relation List 35
- Use DHCP Software to 36
- Configure Your Adapter 36
- Set Up the Hardware 38
- Create the Example 39
- Application 39
- Configure the I/O Modules 40
- New Module 41
- Name Local_ENBT 42
- IP Address 10.88.70.4 42
- Add the POINT I/O Adapter 44
- Name POINT IO Adapter 45
- IP Address 10.88.70.2 45
- IMPORTANT 45
- 1734-SG001 48
- The New Module dialog opens 49
- Ethernet 53
- Edit the Controller Tags 54
- Create the Ladder Program 55
- Download the Program to 55
- Verify the Module Chassis 56
- 3. Select Properties 57
- 4. Click the Connection tab 57
- Configure the Adapter with 59
- Fixed IP Address 59
- Recover From an 60
- Overloaded Adapter 60
- Software 61
- Connection 72
- 72
- 10. Click OK 77
- Verify the Module 79
- Chassis Size 79
- 8. Click OK to continue 80
- Access Module Data 82
- Troubleshoot the Adapter 83
- 1738-AENTR 86
- Series B 86
- Specifications 89
- Power Supply 91
- EtherNet Communication 91
- Environmental 92
- Adapter Web Dialogs 93
- Work with the Diagnostics 95
- Download EDS files for 96
- Use the Network Settings Page 97
- Use the I/O Connections Page 100
- Work with the 102
- Configuration Pages 102
- Use the Identity Page 104
- Use the Services Page 106
- Work with the Browse 107
- Chassis Page 107
- If there is no response to 108
- Communication Driver 109
- Configure the AB_ETH/IP 112
- Rockwell Automation Support 120
- Documentation Feedback 120
Relacionado con productos y manuales para Equipo Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O
Equipo Rockwell-automation 1769-OA8 Compact 100 to 240V ac Solid State Output Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1734-PDN/B Point I/O DeviceNet Communication Inter Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1786-RPFRXL ControlNet Fiber Ring Modules Installa Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 1732E-XXXX ArmorBlock 2-Port EtherNet/IP Modules w Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1746-Px SLC 500 Power Supplies Installation Instru Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1771-OFE/B Analog Output Module User Manual Manual de usuario
(84 paginas)
(84 paginas)
Equipo Rockwell-automation 1738-8CFGM23 ArmorPoint Module with Configurable 2 Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1769-OA16 Compact 16-Point 100 to 240V ac Output M Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1792D-8BVT8D ArmorBlock MaXum 8 Input/8 Output Mod Manual de usuario
(16 paginas)
(16 paginas)
BlackWing Projectors user manuals
The list of BlackWing Projectors products contains 1 user manuals for 1 models. All pdf user’s guides are available for download or viewing online.
Comentarios a estos manuales