Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O Manual de usuario Pagina 38
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
30 Rockwell Automation Publication 1734-UM017B-EN-P - October 2013
Chapter 4 Configure the Adapter for Direct Connection in RSLogix 5000 Software
Set Up the Hardware
The following section describes how to set up the I/O Hardware.
In this example, a ControlLogix chassis contains the L63 controller in slot 1 and a
1756-ENBT bridge module in slot 3. The 1734-AENTR/B adapter is mounted
on a DIN rail in slot 0, with a 1734-OW2/C relay output module in slot 1, a
1734-OV4E/C sink output module in slot 2, and a power supply (not shown).
To work along with this example, set up your system as shown in the figure.
• In the example application, we assume that the L63 controller and
1756-ENBT module (firmware revision 2.3, or later) are in the slots shown
in the figure.
• Verify the IP addresses for your programming terminal, 1756-ENBT
module, and adapter.
• Verify the position (slot) of the I/O modules on the DIN rail.
• Verify that you connected all wiring and cabling properly.
• Be sure you configured your communication driver (for example,
AB_ETH-1 or AB-ETHIP-1) in RSLinx software, as described in
Appendix C
in this manual.
Local
chassis
POINT I/O
L63
controller (slot 1)
1756-ENBT
10.88.70.4 (slot 3)
Data
Switch
10.88.70.26
Programming
terminal
Slot 0 1 2 3
1734-AENTR
10.88.70.2
Slot 0 1 2 3 4
02
0
1734-AENTR Series B
Module
Status
Network
Activity
Network
Status
Point Bus
Status
System
Power
Field
Power
POINT I O
Link 1
Activity/
Status
Link 2
Activity/
Status
IP ADDRESS
45176
- EtherNet/IP Adapters 1
- Important User Information 2
- Who Should Use this 3
- Purpose of this Manual 3
- Common Techniques Used 4
- Table of Contents 5
- Adapter Features 9
- What the Adapter Does 10
- Physical Features of Your 11
- Adapters 11
- software releases 12
- chassis size 12
- Replacement 13
- Use of the Common 14
- Industrial Protocol (CIP) 14
- Chapter Summary 16
- Overview 17
- A = DIN rail 18
- Install POINT I/O Modules 19
- Remove POINT I/O Modules 19
- Remove ArmorPoint I/O Modules 22
- Replace An Adapter 23
- Wire the Adapter 24
- for more information 26
- third party DHCP server 27
- Configuration 28
- Requirements 28
- Gateway Address 29
- Subnet Mask 30
- Network Address 31
- Use the Rockwell BootP/ 32
- DHCP Utility 32
- 1. Run the BootP software 33
- Save the Relation List 35
- Use DHCP Software to 36
- Configure Your Adapter 36
- Set Up the Hardware 38
- Create the Example 39
- Application 39
- Configure the I/O Modules 40
- New Module 41
- Name Local_ENBT 42
- IP Address 10.88.70.4 42
- Add the POINT I/O Adapter 44
- Name POINT IO Adapter 45
- IP Address 10.88.70.2 45
- IMPORTANT 45
- 1734-SG001 48
- The New Module dialog opens 49
- Ethernet 53
- Edit the Controller Tags 54
- Create the Ladder Program 55
- Download the Program to 55
- Verify the Module Chassis 56
- 3. Select Properties 57
- 4. Click the Connection tab 57
- Configure the Adapter with 59
- Fixed IP Address 59
- Recover From an 60
- Overloaded Adapter 60
- Software 61
- Connection 72
- 72
- 10. Click OK 77
- Verify the Module 79
- Chassis Size 79
- 8. Click OK to continue 80
- Access Module Data 82
- Troubleshoot the Adapter 83
- 1738-AENTR 86
- Series B 86
- Specifications 89
- Power Supply 91
- EtherNet Communication 91
- Environmental 92
- Adapter Web Dialogs 93
- Work with the Diagnostics 95
- Download EDS files for 96
- Use the Network Settings Page 97
- Use the I/O Connections Page 100
- Work with the 102
- Configuration Pages 102
- Use the Identity Page 104
- Use the Services Page 106
- Work with the Browse 107
- Chassis Page 107
- If there is no response to 108
- Communication Driver 109
- Configure the AB_ETH/IP 112
- Rockwell Automation Support 120
- Documentation Feedback 120
Relacionado con productos y manuales para Equipo Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O
Equipo Rockwell-automation 1769-OA8 Compact 100 to 240V ac Solid State Output Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1734-PDN/B Point I/O DeviceNet Communication Inter Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1786-RPFRXL ControlNet Fiber Ring Modules Installa Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 1732E-XXXX ArmorBlock 2-Port EtherNet/IP Modules w Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1746-Px SLC 500 Power Supplies Installation Instru Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1771-OFE/B Analog Output Module User Manual Manual de usuario
(84 paginas)
(84 paginas)
Equipo Rockwell-automation 1738-8CFGM23 ArmorPoint Module with Configurable 2 Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1769-OA16 Compact 16-Point 100 to 240V ac Output M Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1792D-8BVT8D ArmorBlock MaXum 8 Input/8 Output Mod Manual de usuario
(16 paginas)
(16 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales