Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O Manual de usuario Pagina 61
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication 1734-UM017B-EN-P - October 2013 53
Chapter
5
Configure the Adapter for Direct Connection
and Rack Optimization in RSLogix 5000
Software
Overview
This chapter guides you through the steps required to configure your AENTR
adapter with both direct and rack-optimized I/O connections using
RSLogix 5000 software.
You can mix I/O connection formats for different I/O modules communicating
through the same adapter. I/O modules set up to use rack optimization
communicate at the rate of the RPI configured for the adapter.
I/O modules controlled by a direct I/O connection communicate at their own set
RPI. The RPI of the rack-optimized I/O connection has no bearing on the direct
I/O connections. The modules presented in this chapter have a configuration
using RSLogix 5000 software, revision 11. The chapter contains the following
main sections
.
Topic Page
Set Up the Hardware 54
Create the Example Application 55
Configure the I/O Modules 56
Add the Local EtherNet/IP Bridge to the I/O Configuration 56
Add the POINT I/O Adapter to the I/O Configuration 60
Add the POINT I/O Modules and Configure for Rack-optimized Connection 64
Add the POINT I/O Module and Configure For Direct Connection 66
Download the Program to the Controller 70
Verify the Module Chassis Size 71
Access Module Data 74
ATTENTION: You must only use Series C and above POINT I/O modules
with 1734-AENTR EtherNet/IP Adapters. Series A or Series B POINT I/O
modules do not work with 1734-AENTR EtherNet/IP Adapters (does not
apply to POINTGuard modules).
- EtherNet/IP Adapters 1
- Important User Information 2
- Who Should Use this 3
- Purpose of this Manual 3
- Common Techniques Used 4
- Table of Contents 5
- Adapter Features 9
- What the Adapter Does 10
- Physical Features of Your 11
- Adapters 11
- software releases 12
- chassis size 12
- Replacement 13
- Use of the Common 14
- Industrial Protocol (CIP) 14
- Chapter Summary 16
- Overview 17
- A = DIN rail 18
- Install POINT I/O Modules 19
- Remove POINT I/O Modules 19
- Remove ArmorPoint I/O Modules 22
- Replace An Adapter 23
- Wire the Adapter 24
- for more information 26
- third party DHCP server 27
- Configuration 28
- Requirements 28
- Gateway Address 29
- Subnet Mask 30
- Network Address 31
- Use the Rockwell BootP/ 32
- DHCP Utility 32
- 1. Run the BootP software 33
- Save the Relation List 35
- Use DHCP Software to 36
- Configure Your Adapter 36
- Set Up the Hardware 38
- Create the Example 39
- Application 39
- Configure the I/O Modules 40
- New Module 41
- Name Local_ENBT 42
- IP Address 10.88.70.4 42
- Add the POINT I/O Adapter 44
- Name POINT IO Adapter 45
- IP Address 10.88.70.2 45
- IMPORTANT 45
- 1734-SG001 48
- The New Module dialog opens 49
- Ethernet 53
- Edit the Controller Tags 54
- Create the Ladder Program 55
- Download the Program to 55
- Verify the Module Chassis 56
- 3. Select Properties 57
- 4. Click the Connection tab 57
- Configure the Adapter with 59
- Fixed IP Address 59
- Recover From an 60
- Overloaded Adapter 60
- Software 61
- Connection 72
- 72
- 10. Click OK 77
- Verify the Module 79
- Chassis Size 79
- 8. Click OK to continue 80
- Access Module Data 82
- Troubleshoot the Adapter 83
- 1738-AENTR 86
- Series B 86
- Specifications 89
- Power Supply 91
- EtherNet Communication 91
- Environmental 92
- Adapter Web Dialogs 93
- Work with the Diagnostics 95
- Download EDS files for 96
- Use the Network Settings Page 97
- Use the I/O Connections Page 100
- Work with the 102
- Configuration Pages 102
- Use the Identity Page 104
- Use the Services Page 106
- Work with the Browse 107
- Chassis Page 107
- If there is no response to 108
- Communication Driver 109
- Configure the AB_ETH/IP 112
- Rockwell Automation Support 120
- Documentation Feedback 120
Relacionado con productos y manuales para Equipo Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O
Equipo Rockwell-automation 1769-OA8 Compact 100 to 240V ac Solid State Output Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1734-PDN/B Point I/O DeviceNet Communication Inter Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1786-RPFRXL ControlNet Fiber Ring Modules Installa Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 1732E-XXXX ArmorBlock 2-Port EtherNet/IP Modules w Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1746-Px SLC 500 Power Supplies Installation Instru Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1771-OFE/B Analog Output Module User Manual Manual de usuario
(84 paginas)
(84 paginas)
Equipo Rockwell-automation 1738-8CFGM23 ArmorPoint Module with Configurable 2 Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1769-OA16 Compact 16-Point 100 to 240V ac Output M Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1792D-8BVT8D ArmorBlock MaXum 8 Input/8 Output Mod Manual de usuario
(16 paginas)
(16 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales