Rockwell-automation 198 Series C Modular DeviceNet Starter Auxiliary U Manual de usuario Pagina 47
- Pagina / 176
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation 3-26
Publication 198-UM002A-EN-P December 2001
Mod/Net Status LED
The Module/Network Status LED is a bi-colored (red/green) LED that provides status
information on DeviceNet communications. Table 3.6 on page 3-26 summarizes the
operation of the LED.
I/O Status LED
The I/O status LED is a bi-colored (red/green) LED that provides status information on
communications between the I/O module.
Table 3.6 LED Operation
For this state: MS/NS LED is: To indicate:
Powerup and Autobaud Flashes
green-red-off
When power is connected, the LED will flash this pattern
one time. When waiting to detect the baud rate, the LED
will flash this pattern about every 3 seconds.
Not Powered/Not
On-line/ Device is not on-line
Off The device has not completed the Dup_MAC_ID test yet.
The device may not be powered.
Device Operational AND
On-line, Connected
Green The device is operating in a normal condition and the
device is on-line with connections in the established state.
Device Operational AND
On-line, Not Connected or
Device On-line AND needs
commissioning
Flashing Green The device is operating in a normal condition and the
device is on-line with no connections in the established
state. The device has passed the Dup_Mac_ID test, is
on-line, but has no established connections to other nodes.
Minor Fault and/or
Connection Time-Out
Flashing Red Recoverable fault and/ or one or more I/O connections are
in the Timed-Out state.
Critical Fault or Critical Link
Failure
Red The device has an unrecoverable fault; may need replacing.
Failed communication device. The device has detected an
error that has rendered it incapable of communicating on
the network (Duplicate MAC ID, or Bus-off).
Communication Faulted and
Received and Identify Comm
Fault Request- Long Protocol
Flashing Red &
Green
A specific Communication Faulted device. The device has
detected a Network Access error and is in the
Communication Faulted state. The device has subsequently
received and accepted an Identify Communication Faulted
Request- Long Protocol message
Table 3.7 I/O Status LED
For This State: I/O Status
LED is:
To indicate:
Off Off No power or All outputs in the inactive state. Configuration of I/O
modules good.
I/O Idle Flashing Green The DeviceNet network has caused the outputs to be in their idle state.
Idle/ Program mode.
I/O Run Green Outputs are active.
I/O Recoverable Fault Flashing Red A connection controlling the outputs has timed out.
I/O Unrecoverable
Fault
Red Configuration of I/ O Module does not match saved configuration.
Power-up initialization of bus power failed.
CSUM Error at the module “X”.
Invalid Module ID “X”.
- Modular DeviceNet 1
- Starter Auxiliary 1
- Important User Information 2
- EMC Directive 3
- Low Voltage Directive 3
- Manual Objectives 4
- Intended Audience 4
- Vocabulary 5
- Reference Manuals 5
- Table of Contents 7
- Chapter 4 — Programming 8
- Chapter 5 — Specifications 8
- Chapter 6 — Troubleshooting 8
- Product Overview 11
- 198-IB2XOW1 or similar 12
- 198-IB2S 12
- 198 – DNG 14
- 198 – IB2XOB2S-Q5 14
- Installation 15
- Electrostatic Discharge 16
- Remove Power 16
- Approximate Dimensions 17
- Module Installation 18
- DIN Rail Mounting 18
- Gland Plate Mounting 19
- 1492-SM8X9 20
- Wiring Diagrams 21
- Operation 22
- 3-5 Operation 26
- Node Address 27
- Address 63 Shown 27
- Autobaud Configuration 28
- Mapping to the Scanner 31
- Advanced Topics 33
- Operation 3-16 37
- COS Mask Parameters 39
- IO Mod COS Mask 39
- Net Out COS Mask 40
- Input Filtering 41
- DeviceNet Explicit Messaging 41
- I/O Modules and DeviceNet 42
- Sample Module Assembly 42
- Table 3.3 Instance Table 43
- Table 3.4 Blank Table 44
- Mod/Net Status LED 47
- I/O Status LED 47
- Programming 48
- Verifying the Input Assembly 51
- Verifying the Output Assembly 53
- Programming Explicit Messages 55
- Specifications 60
- Table 5.1 Mod/Net Status LED 61
- Specifications 5-4 63
- 5-5 Specifications 64
- Specifications 5-6 65
- 5-7 Specifications 66
- 198-IB2S (Sensor Module) 67
- 5-9 Specifications 68
- Specifications 5-10 69
- 198-IB4 (4-Input DC Module) 70
- Specifications 5-12 71
- 5-13 Specifications 72
- 5-15 Specifications 74
- Specifications 5-16 75
- 198-IA2 (2-Input AC Module) 76
- Specifications 5-18 77
- 5-19 Specifications 78
- 5-21 Specifications 80
- Specifications 5-22 81
- Specifications 5-24 83
- 5-25 Specifications 84
- 5-27 Specifications 86
- 5-29 Specifications 88
- Specifications 5-30 89
- 5-33 Specifications 92
- 5-35 Specifications 94
- AC Starter DOL 97
- AC Starter Reversing 98
- 5-41 Specifications 100
- Series A to Series B Changes 101
- Output 1 102
- M – contactor 103
- MS – manual start 103
- Bulletin 190 Compact Starter 104
- Series B Module 105
- 5-47 Specifications 106
- Specifications 5-48 107
- 120/240V AC 109
- DC Input Relay Output 110
- 120/240 V AC 111
- Series B module 112
- Specifications 5-54 113
- 5-55 Specifications 114
- 5-57 Specifications 116
- DRIVE MODULE 117
- 5-61 Specifications 120
- 5-63 Specifications 122
- 198-G1P (Gland Plates) 126
- Specifications 5-68 127
- 5-69 Specifications 128
- 5-71 Specifications 130
- Troubleshooting 131
- Red I/O Light — Noise 132
- Low DeviceNet Voltage 132
- Excessive Number of Modules 133
- Invalid ID 133
- Checksum Error 133
- Discontinuity Error 133
- I/O Module Current Errors 134
- Sensor Undervoltage Error 134
- DeviceNet Information 135
- Operating Modes 136
- Run Mode 137
- Error Mode 137
- I/O Error Mode 137
- I/O Idle Mode 137
- DeviceNet Object Definitions 138
- Table A.3 139
- Table A.4 139
- Table A.5 139
- Message Router 140
- DeviceNet Object 140
- Assembly Object 141
- Table A.11 142
- Table A.13 143
- Instance 102 144
- Instance 104 144
- Instance 106 145
- Instance 110 145
- Instance 111 146
- Instance 112 147
- Table A.20 148
- Instance 103 149
- Instance 105 149
- Instance 107 150
- Instance 100 152
- Instance 101 153
- Assembly Instance 120 154
- Assembly Instance 121 154
- Instance 180 155
- Instance 181 155
- Instance 182 155
- Instance 183 155
- Instance 184 155
- Instance 185 156
- Instance 186 156
- Instance 187 156
- Instance 188 156
- Instance 189 157
- Instance 190 157
- Assembly Object Services 157
- I/O Assembly Instance Summary 158
- Connection Object 159
- Discrete Input Point Object 162
- Discrete Output Point Object 163
- Discrete Input Group Object 164
- Discrete Output Group Object 164
- Acknowledge Handler Object 165
- DeviceNet Interface Object 165
- Table A.62 166
- Table A.63 168
- Motor Starter Operation 169
- Table B.1 170
- Motor Starter I/O Assemblies 171
- Control Supervisor Object 174
- Overload Object 174
Relacionado con productos y manuales para Equipo Rockwell-automation 198 Series C Modular DeviceNet Starter Auxiliary U
Equipo Rockwell-automation 191S-A_B_C_D Bul 191S Reversing Compact Starter Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1492-ACAB_B7H Pre-wired Cables for PowerFlex 700H Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 440T Prosafe Rotary Key Switch-Panel Mounted Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation W40751-468-xx Bul 193 Ranger Overload Relay Replac Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 150- SMC-3 Soft Starter N.C. Fault Contact (3 Phas Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 25B Bulletin 160 to PowerFlex 520-Series Adapter P Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales