Rockwell-automation 20G PowerFlex 755 Drive Embedded EtherNet/IP Adapt Manual de usuario Pagina 134
- Pagina / 190
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
134 Rockwell Automation Publication 750COM-UM001E-EN-P - October 2013
Appendix B Adapter Parameters
78 [Logic Src Cfg]
Controls which of the peer-to-drive Datalinks contain the Logic
Command for the drive. The value zero specifies that none of the
Datalinks contain the drive’s Logic Command. Non-zero values
specify the ‘index’ for the Datalink containing the drive’s Logic
Command. For example, if Parameter 76 - [DLs Fr Peer Cfg]
has the value 3 specifying that Datalinks 14…16 are allocated
for peer I/O and Parameter 78 - [Logic Src Cfg] has the value 1
specifying that the first peer I/O Datalink contains the drive’s
Logic Command, then Datalink 14 contains the drive’s Logic
Command.
NOTE: The adapter allows the peer input configuration
parameters to be written while peer inputs are running.
However, the changes will not take effect until peer inputs are
disabled and then re-enabled, or until the adapter is power
cycled or reset.
Default: 0
Minimum: 0
Maximum: 16
Type: Read/Write
Reset Required: No
79 [Ref Src Cfg]
Controls which of the peer-to-drive Datalinks contain the
Reference for the drive. The value zero specifies that none of the
Datalinks contain the drive’s Reference. Non-zero values specify
the ‘index’ for the Datalink containing the drive’s Reference. For
example, if Parameter 76 - [DLs Fr Peer Cfg] has the value 3
specifying that Datalinks 14…16 are allocated for peer I/O and
Parameter 79 - [Ref Src Cfg] has the value 1 specifying that
the first peer I/O Datalink contains the drive’s Reference, then
Datalink 14 contains the drive’s Reference.
NOTE: The adapter allows the peer input configuration
parameters to be written while peer inputs are running.
However, the changes will not take effect until peer inputs are
disabled and then re-enabled, or until the adapter is power
cycled or reset.
Default: 0
Minimum: 0
Maximum: 16
Type: Read/Write
Reset Required: No
80 [Fr Peer Timeout]
Sets the timeout for a peer I/O connection. If the time is reached
without the adapter receiving (consuming) a message, the
adapter will respond with the action specified in Parameter 56
- [Peer Flt Action].
In an adapter receiving (consuming) peer I/O, the value of this
parameter must be greater than the product of the value of
Parameter 89 - [To Peer Period] in the adapter transmitting
(producing) peer I/O multiplied by the value of Parameter 90 -
[To Peer Skip] in the adapter transmitting (producing) peer I/O.
NOTE: The adapter allows the peer input configuration
parameters to be written while peer inputs are running.
However, the changes will not take effect until peer inputs are
disabled and then re-enabled, or until the adapter is power
cycled or reset.
Default: 10.00 Seconds
Minimum: 0.01 Seconds
Maximum: 10.00 Seconds
Type: Read/Write
Reset Required: No
Parameter
No. Name and Description Details
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Conventions Used in This 9
- Rockwell Automation 9
- Additional Resources 10
- Getting Started 11
- Features 12
- Compatible Products 13
- Required Equipment 13
- Chapter 1 Getting Started 14
- Safety Precautions 15
- Quick Start 16
- Installing the Adapter 17
- Setting the IP Address 18
- Connecting the Adapter to 20
- Applying Power 21
- Commissioning the Adapter 24
- Configuring the Adapter 25
- Using the PowerFlex 20-HIM 26
- A6 or 20-HIM-C6S HIM to 26
- Access Parameters 26
- Setting the Adapter IP 26
- Enabled 1 27
- Disable the BOOTP Feature 30
- Set the IP Address 30
- Set the Subnet Mask 30
- Setting the Data Rate 31
- Selecting Master-Slave or 32
- Peer-to-Peer Hierarchy 32
- Enable Datalinks To Read Data 33
- 0<<2 35
- Custom Peer I/O Configuration 36
- 10.00 Secs 37
- Setting a Fault Action 38
- Setting Web Access Control 40
- Resetting the Adapter 41
- Restoring Adapter 41
- Parameters to Factory 41
- Defaults 41
- ESC soft 42
- Viewing the Adapter Status 42
- Using Parameters 42
- Updating the Adapter 43
- Firmware 43
- Configuring the I/O 45
- ControlLogix Example 46
- Chapter 4 Configuring the I/O 50
- Configuring the I/O Chapter 4 53
- ADC and Logix Memory 66
- Monitoring ADC Progress 71
- Using the I/O 79
- Understanding the 80
- ControlLogix Controller I/O 80
- Using Logic Command/Status 81
- Using Reference/Feedback 81
- Using Datalinks 82
- Example Ladder Logic 83
- Program Information 83
- ControlLogix Controller 84
- Using the I/O Chapter 5 85
- Versions 86
- Program 87
- Program Tags 88
- Example Datalink Data 89
- Generic Profile 90
- Using Explicit Messaging 91
- About Explicit Messaging 92
- Examples 94
- Single Parameter 96
- Multiple Parameters 101
- Request (Source Data) array 105
- Troubleshooting 107
- ENET Status Indicator 108
- LINK Status Indicator 108
- Viewing Adapter Diagnostic 109
- Viewing and Clearing Events 111
- Table 12 - Adapter Events 112
- Viewing the Adapter Web Pages 113
- Process Display Pop-up 116
- Dialog Box 116
- TCP/IP Configuration Web 117
- Web Page 118
- Device Information Pages 121
- EtherNet/IP adapter) 123
- Specifications 125
- Appendix A Specifications 126
- Adapter Parameters 127
- Parameter List 128
- EtherNet/IP Objects 137
- Identity Object 138
- Assembly Object 139
- Register Object 140
- PCCC Object 141
- N-Files 143
- DPI Device Object 145
- Class Attributes 146
- Instance Attributes 147
- DPI Parameter Object 148
- Formula number 150
- Extended DPI descriptor 150
- Descriptor Attributes 151
- Formulas for Converting 153
- Common Services 153
- Object Specific Services 153
- DPI Fault Object 154
- DPI Alarm Object 156
- DPI Diagnostic Object 158
- DPI Time Object 160
- Host DPI Parameter Object 162
- TCP/IP Interface Object 168
- Ethernet Link Object 170
- 750-Series Drives 173
- History of Changes 175
- Glossary 177
- Rockwell Automation Support 190
- Documentation Feedback 190
Relacionado con productos y manuales para Equipo Rockwell-automation 20G PowerFlex 755 Drive Embedded EtherNet/IP Adapt
Equipo Rockwell-automation 440P-WM5 Telescopic Arm Installation/Operating Ins Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 190 Universal Instruction Sheet for Open Type Star Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 440K Cadet 3 GD2 Compact Tongue Operated Interlock Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 592-ECxHF E3 NEMA Size 5 Overload Relay Installati Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 194RF-xxxx Front-Operating Disconnect and Handle w Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 509-TA_ Size 00 Enclosure Cover Replacement Manual de usuario
(1 paginas)
(1 paginas)
Equipo Rockwell-automation 825P Modular Protection System Quick Start Guide Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation 150-SBFC SMC-50 Soft Starter Fan Cover Installatio Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 281G ArmorStart - Safety Version - Getting Started Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 25B PowerFlex 520-Series IP30/NEMA 1/UL Type 1 Kit Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales