Rockwell-automation 20G PowerFlex 755 Drive Embedded EtherNet/IP Adapt Manual de usuario Pagina 39
- Pagina / 190
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication 750COM-UM001E-EN-P - October 2013 39
Configuring the Adapter Chapter 3
Changing the Fault Action
Set the values of Parameters 54 - [Comm Flt Action], 55 - [Idle Flt Action], 56
- [Peer Flt Action], and 57 - [Msg Flt Action] to an action that meets your
application requirements.
Figure 5 - Edit Fault Action HIM Screens
Changes to these parameters take effect immediately. A reset is not required.
If communication is disrupted and then re-established, the drive will
automatically receive commands over the network again.
Setting the Fault Configuration Parameters
When setting Parameter 54 - [Comm Flt Action], 55 - [Idle Flt Action], 56 -
[Peer Flt Action] or Parameter 57 - [Msg Flt Action] to ‘Send Flt Cfg’, the
values in the following parameters are sent to the drive after a communication
fault, idle fault, peer I/O fault, and/or explicit messaging for drive control fault
ATTENTION: Risk of injury or equipment damage exists. Embedded adapter
Parameters 54 - [Comm Flt Action], 55 - [Idle Flt Action], 56 - [Peer Flt
Action], and 57 - [Msg Flt Action] respectively let you determine the action of
the adapter and drive if communication is disrupted, the controller is idle, peer
I/O is disrupted, or explicit messaging for drive control is disrupted. By default,
these parameters fault the drive. You may configure these parameters so that the
drive continues to run, however, precautions should be taken to verify that the
settings of these parameters do not create a risk of injury or equipment damage.
When commissioning the drive, verify that your system responds correctly to
various situations (for example, a disconnected network cable, controller in idle
state or explicit message control disruption).
Value Action Description
0 Fault The drive is faulted and stopped. (Default)
1 Stop The drive is stopped, but not faulted.
2 Zero Data The drive is sent ‘0’ values for data. This does not command a stop.
3 Hold Last The drive continues in its present state.
4 Send Flt Cfg The drive is sent the data that you set in the fault configuration parameters (Parameters 58
- [Flt Cfg Logic], 59 - [Flt Cfg Ref], and 60 - [Flt Cfg DL 01] through 75 - [Flt Cfg DL 16]).
ESC
ENTER
Stopped
0.00 Hz
AUTO
F
▲▼
Edit Comm Flt Action
Fault 0
0<<4
ESC
ENTER
Stopped
0.00 Hz
AUTO
F
▲▼
Edit Idle Flt Action
Fault 0
0<<4
ESC
ENTER
Stopped
0.00 Hz
AUTO
F
▲▼
Edit Msg Flt Action
Fault 0
0<<4
ESC
ENTER
Stopped
0.00 Hz
AUTO
F
▲▼
Edit Peer Flt Action
Fault 0
0<<4
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Conventions Used in This 9
- Rockwell Automation 9
- Additional Resources 10
- Getting Started 11
- Features 12
- Compatible Products 13
- Required Equipment 13
- Chapter 1 Getting Started 14
- Safety Precautions 15
- Quick Start 16
- Installing the Adapter 17
- Setting the IP Address 18
- Connecting the Adapter to 20
- Applying Power 21
- Commissioning the Adapter 24
- Configuring the Adapter 25
- Using the PowerFlex 20-HIM 26
- A6 or 20-HIM-C6S HIM to 26
- Access Parameters 26
- Setting the Adapter IP 26
- Enabled 1 27
- Disable the BOOTP Feature 30
- Set the IP Address 30
- Set the Subnet Mask 30
- Setting the Data Rate 31
- Selecting Master-Slave or 32
- Peer-to-Peer Hierarchy 32
- Enable Datalinks To Read Data 33
- 0<<2 35
- Custom Peer I/O Configuration 36
- 10.00 Secs 37
- Setting a Fault Action 38
- Setting Web Access Control 40
- Resetting the Adapter 41
- Restoring Adapter 41
- Parameters to Factory 41
- Defaults 41
- ESC soft 42
- Viewing the Adapter Status 42
- Using Parameters 42
- Updating the Adapter 43
- Firmware 43
- Configuring the I/O 45
- ControlLogix Example 46
- Chapter 4 Configuring the I/O 50
- Configuring the I/O Chapter 4 53
- ADC and Logix Memory 66
- Monitoring ADC Progress 71
- Using the I/O 79
- Understanding the 80
- ControlLogix Controller I/O 80
- Using Logic Command/Status 81
- Using Reference/Feedback 81
- Using Datalinks 82
- Example Ladder Logic 83
- Program Information 83
- ControlLogix Controller 84
- Using the I/O Chapter 5 85
- Versions 86
- Program 87
- Program Tags 88
- Example Datalink Data 89
- Generic Profile 90
- Using Explicit Messaging 91
- About Explicit Messaging 92
- Examples 94
- Single Parameter 96
- Multiple Parameters 101
- Request (Source Data) array 105
- Troubleshooting 107
- ENET Status Indicator 108
- LINK Status Indicator 108
- Viewing Adapter Diagnostic 109
- Viewing and Clearing Events 111
- Table 12 - Adapter Events 112
- Viewing the Adapter Web Pages 113
- Process Display Pop-up 116
- Dialog Box 116
- TCP/IP Configuration Web 117
- Web Page 118
- Device Information Pages 121
- EtherNet/IP adapter) 123
- Specifications 125
- Appendix A Specifications 126
- Adapter Parameters 127
- Parameter List 128
- EtherNet/IP Objects 137
- Identity Object 138
- Assembly Object 139
- Register Object 140
- PCCC Object 141
- N-Files 143
- DPI Device Object 145
- Class Attributes 146
- Instance Attributes 147
- DPI Parameter Object 148
- Formula number 150
- Extended DPI descriptor 150
- Descriptor Attributes 151
- Formulas for Converting 153
- Common Services 153
- Object Specific Services 153
- DPI Fault Object 154
- DPI Alarm Object 156
- DPI Diagnostic Object 158
- DPI Time Object 160
- Host DPI Parameter Object 162
- TCP/IP Interface Object 168
- Ethernet Link Object 170
- 750-Series Drives 173
- History of Changes 175
- Glossary 177
- Rockwell Automation Support 190
- Documentation Feedback 190
Relacionado con productos y manuales para Equipo Rockwell-automation 20G PowerFlex 755 Drive Embedded EtherNet/IP Adapt
Equipo Rockwell-automation 440P-WM5 Telescopic Arm Installation/Operating Ins Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 190 Universal Instruction Sheet for Open Type Star Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 440K Cadet 3 GD2 Compact Tongue Operated Interlock Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 592-ECxHF E3 NEMA Size 5 Overload Relay Installati Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 194RF-xxxx Front-Operating Disconnect and Handle w Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 509-TA_ Size 00 Enclosure Cover Replacement Manual de usuario
(1 paginas)
(1 paginas)
Equipo Rockwell-automation 825P Modular Protection System Quick Start Guide Manual de usuario
(32 paginas)
(32 paginas)
Equipo Rockwell-automation 150-SBFC SMC-50 Soft Starter Fan Cover Installatio Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 281G ArmorStart - Safety Version - Getting Started Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 25B PowerFlex 520-Series IP30/NEMA 1/UL Type 1 Kit Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.126 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales