Rockwell-automation 1440-DYN02-01RJ XM Dynamic Measurement Module Manual de usuario Pagina 150
- Pagina / 160
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
150 Publication ICM-UM002F-EN-E - March 2013
Appendix B CIP Objects
Instance Attributes
Services
Table B.52 Vector Measurement Object Instance Attributes
Attr ID
Access
Rule Name Data Type Description Semantics
3 Get Magnitude
Value
REAL The measured magnitude
value.
4 Get Phase Value REAL The measured phase
value.
Degrees
Note: Not valid for instances 5
and 6.
5 Get Status BOOL Indicates if a fault or
alarm has occurred.
0 = Operating without alarms of
faults.
1 = Alarm or fault condition
exists. The Value attributes
may not represent the actual
field value.
6 Get Magnitude Data
Units
ENGUNIT The units context of the
Magnitude Value
attribute.
This setting is determined by the
Channel Object’s Output Data
Units setting (see page 128
).
7 Get Speed Value REAL The speed at which the
magnitude and phase are
measured.
Instances 1 and 2 use 1X
machine speed.
Instances 3 and 4 use 2X
machine speed.
Instances 5 and 6 use 3X
machine speed.
The value is only valid when
synchronous sampling mode is
selected for the corresponding
channel.
8 Get Speed Data
Units
ENGUNIT The units context of the
Speed Value attribute.
See DeviceNet Specification
Volume 1 Appendix K.
This is set to Orders.
Table B.53 Vector Measurement Object Services
Service
Code Class/Instance Usage Name Description
0E
h
Instance Get_Attribute_Single Returns a single attribute.
- XM Dynamic Measurement Module 1
- Important User Information 2
- Table of Contents 3
- Additional Resources 8
- Introduction 9
- Module Components 10
- Introduction Chapter 1 11
- ATTENTION 11
- Chapter 1 Introduction 12
- XM Installation 18
- Requirements 18
- Grounding Requirements 19
- DIN Rail Grounding 20
- Panel/Wall Mount Grounding 21
- 24V Common Grounding 22
- Terminating Resistors 23
- Mounting the Terminal 24
- Base Unit 24
- IMPORTANT 25
- Panel/Wall Mounting 26
- Connecting Wiring for Your 27
- Terminal Block Assignments 28
- Connecting the Power Supply 30
- Terminal Base #1 32
- Terminal Base #2 32
- Terminal Base #3 32
- Shielded Tacho Sensor 32
- Tach Input Signal 33
- Connecting the Transducer 34
- Channel 0 Input Signal 35
- Signal Common 38
- Connecting a Powered Sensor 39
- XM Bus Connection 47
- Mounting the Module 49
- Basic Operations 50
- DYNAMIC MEASUREMENT 51
- 1440-DYN02-01RJ 51
- Configure the Module 53
- Software 55
- Add the XM Module to the 56
- I/O Configuration Tree 56
- Profiles 57
- 6. Click OK 58
- Configure Module 59
- Properties 59
- Configure the Band Properties 75
- Clear to disable the alarm 78
- Troubleshoot the Module 87
- I/O Data Tags 91
- Module-defined Data Types 92
- Ch0SumHarmonics 94
- Ch1SumHarmonics 95
- Configuration Data Type 96
- Output Data Type 101
- CIP Objects 103
- Identity Object 104
- (Class Code 01 104
- DeviceNet Object 106
- (Class Code 03 106
- (Class Code 04 107
- Assembly Object 107
- Instances 108
- Instance Attributes 108
- Status values change 109
- Request from a Master 109
- Appendix B CIP Objects 110
- CIP Objects Appendix B 111
- Connection Object 112
- (Class ID 05H) 112
- Discrete Input Point Object 114
- (Class ID 08H) 114
- Services 115
- Analog Input Point 116
- (Class ID 0A 116
- Parameter Object 117
- (Class ID 0F 117
- Class Attributes 118
- Acknowledge Handler 122
- (Class ID 2BH) 122
- Alarm Object 123
- (Class ID 31DH) 123
- Band Measurement Object 126
- (Class ID 31E 126
- Channel Object 128
- (Class ID 31F 128
- Device Mode Object 130
- (Class ID 320 130
- Overall Measurement 132
- (Class ID 322 132
- Relay Object 134
- (Class ID 323 134
- Spectrum Waveform 137
- Measurement Object 137
- (Class ID 324 137
- Speed Measurement Object 144
- (Class ID 325 144
- Tachometer Channel Object 145
- (Class ID 326 145
- Transducer Object 147
- (Class ID 328 147
- Vector Measurement 149
- (Class ID 329 149
- Glossary 151
- Numerics 155
- Rockwell Automation Support 160
- Documentation Feedback 160
Relacionado con productos y manuales para Equipo Rockwell-automation 1440-DYN02-01RJ XM Dynamic Measurement Module
Equipo Rockwell-automation MinPak Plus DC Drive Double Pole CB Kit for NRG 14 Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation T8824 Trusted 40 Channel 120V ac Digital Input FTA Manual de usuario
(15 paginas)
(15 paginas)
Equipo Rockwell-automation 1440-DYN02-01RJ XM Dynamic Measurement Module Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation T7833 ICS Regent+Plus Math Package for Winternet Manual de usuario
(26 paginas)
(26 paginas)
Equipo Rockwell-automation 20B PowerFlex 70, PowerFlex 700 Reference Manual Manual de usuario
(214 paginas)
(214 paginas)
Equipo Rockwell-automation 20D PowerFlex 700H/700S AC Drives Frames 13 and 14 Manual de usuario
(18 paginas)
(18 paginas)
Equipo Rockwell-automation PDS- Sprecher+Schuh PDS Soft Starter (6-Lead, Star Manual de usuario
(4 paginas)
(4 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales