Rockwell-automation 1440-DYN02-01RJ XM Dynamic Measurement Module Manual de usuario Pagina 19
- Pagina / 160
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Publication ICM-UM002F-EN-E - March 2013 19
Installing the XM Dynamic Measurement Module Chapter 2
Figure 2.1 XM Modules with Separate Power Connections
Grounding Requirements
Use these grounding requirements to ensure safe electrical operating
circumstances, and to help avoid potential EMI and ground noise that can
cause unfavorable operating conditions for your XM system.
31865
24 V
24 V COM
Supply
XM
®
XM
®
24 V COM
24 V
1
1
1
1
1
1
1
CAN HIGH
XM BUS COMMON
DRAIN WIRE
CAN LOW
Termination
resistor
121 ohm, 1%,
1/4W
Class 2
ATTENTION
To comply with the CE Low Voltage Directive (LVD), all
connections to this equipment must be powered from a source
compliant with the following: Safety Extra Low Voltage (SELV)
or Protected Extra Low Voltage (PELV).
To comply with UL restrictions, this equipment must be
powered from a source compliant with the following: Class 2.
ATTENTION
Multiple power sources are not allowed.
TIP
See Terminal Block Assignments on page 28 for the terminal
block assignments and descriptions for the Dynamic
Measurement module.
- XM Dynamic Measurement Module 1
- Important User Information 2
- Table of Contents 3
- Additional Resources 8
- Introduction 9
- Module Components 10
- Introduction Chapter 1 11
- ATTENTION 11
- Chapter 1 Introduction 12
- XM Installation 18
- Requirements 18
- Grounding Requirements 19
- DIN Rail Grounding 20
- Panel/Wall Mount Grounding 21
- 24V Common Grounding 22
- Terminating Resistors 23
- Mounting the Terminal 24
- Base Unit 24
- IMPORTANT 25
- Panel/Wall Mounting 26
- Connecting Wiring for Your 27
- Terminal Block Assignments 28
- Connecting the Power Supply 30
- Terminal Base #1 32
- Terminal Base #2 32
- Terminal Base #3 32
- Shielded Tacho Sensor 32
- Tach Input Signal 33
- Connecting the Transducer 34
- Channel 0 Input Signal 35
- Signal Common 38
- Connecting a Powered Sensor 39
- XM Bus Connection 47
- Mounting the Module 49
- Basic Operations 50
- DYNAMIC MEASUREMENT 51
- 1440-DYN02-01RJ 51
- Configure the Module 53
- Software 55
- Add the XM Module to the 56
- I/O Configuration Tree 56
- Profiles 57
- 6. Click OK 58
- Configure Module 59
- Properties 59
- Configure the Band Properties 75
- Clear to disable the alarm 78
- Troubleshoot the Module 87
- I/O Data Tags 91
- Module-defined Data Types 92
- Ch0SumHarmonics 94
- Ch1SumHarmonics 95
- Configuration Data Type 96
- Output Data Type 101
- CIP Objects 103
- Identity Object 104
- (Class Code 01 104
- DeviceNet Object 106
- (Class Code 03 106
- (Class Code 04 107
- Assembly Object 107
- Instances 108
- Instance Attributes 108
- Status values change 109
- Request from a Master 109
- Appendix B CIP Objects 110
- CIP Objects Appendix B 111
- Connection Object 112
- (Class ID 05H) 112
- Discrete Input Point Object 114
- (Class ID 08H) 114
- Services 115
- Analog Input Point 116
- (Class ID 0A 116
- Parameter Object 117
- (Class ID 0F 117
- Class Attributes 118
- Acknowledge Handler 122
- (Class ID 2BH) 122
- Alarm Object 123
- (Class ID 31DH) 123
- Band Measurement Object 126
- (Class ID 31E 126
- Channel Object 128
- (Class ID 31F 128
- Device Mode Object 130
- (Class ID 320 130
- Overall Measurement 132
- (Class ID 322 132
- Relay Object 134
- (Class ID 323 134
- Spectrum Waveform 137
- Measurement Object 137
- (Class ID 324 137
- Speed Measurement Object 144
- (Class ID 325 144
- Tachometer Channel Object 145
- (Class ID 326 145
- Transducer Object 147
- (Class ID 328 147
- Vector Measurement 149
- (Class ID 329 149
- Glossary 151
- Numerics 155
- Rockwell Automation Support 160
- Documentation Feedback 160
Relacionado con productos y manuales para Equipo Rockwell-automation 1440-DYN02-01RJ XM Dynamic Measurement Module
Equipo Rockwell-automation MinPak Plus DC Drive Double Pole CB Kit for NRG 14 Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation T8824 Trusted 40 Channel 120V ac Digital Input FTA Manual de usuario
(15 paginas)
(15 paginas)
Equipo Rockwell-automation 1440-DYN02-01RJ XM Dynamic Measurement Module Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation T7833 ICS Regent+Plus Math Package for Winternet Manual de usuario
(26 paginas)
(26 paginas)
Equipo Rockwell-automation 20B PowerFlex 70, PowerFlex 700 Reference Manual Manual de usuario
(214 paginas)
(214 paginas)
Equipo Rockwell-automation 20D PowerFlex 700H/700S AC Drives Frames 13 and 14 Manual de usuario
(18 paginas)
(18 paginas)
Equipo Rockwell-automation PDS- Sprecher+Schuh PDS Soft Starter (6-Lead, Star Manual de usuario
(4 paginas)
(4 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales