Rockwell-automation 1440-DYN02-01RJ XM Dynamic Measurement Module Manual de usuario descargar pdf (Pagina 22)

22 Publication ICM-UM002F-EN-E - March 2013

Chapter 2 Installing the XM Dynamic Measurement Module

Figure 2.4 Panel/Wall Mount Grounding

1 Use 14 AWG wire. If it is desired to isolate the power supply because of possible ground loops, do not connect

24V Common to earth as illustrated in Figure 2.4.

24V Common Grounding

The XM system is sourced by a single Class 2 power supply. It is

recommended that the 24V power to the XM modules is grounded.

Class 2

Supply

Class 2

Supply

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 159 160

XM Dynamic Measurement Module 1
Important User Information 2
Table of Contents 3
Additional Resources 8
Introduction 9
Module Components 10
Introduction Chapter 1 11
ATTENTION 11
Chapter 1 Introduction 12
XM Installation 18
Requirements 18
Grounding Requirements 19
DIN Rail Grounding 20
Panel/Wall Mount Grounding 21
24V Common Grounding 22
Terminating Resistors 23
Mounting the Terminal 24
Base Unit 24
IMPORTANT 25
Panel/Wall Mounting 26
Connecting Wiring for Your 27
Terminal Block Assignments 28
Connecting the Power Supply 30
Terminal Base #1 32
Terminal Base #2 32
Terminal Base #3 32
Shielded Tacho Sensor 32
Tach Input Signal 33
Connecting the Transducer 34
Channel 0 Input Signal 35
Signal Common 38
Connecting a Powered Sensor 39
XM Bus Connection 47
Mounting the Module 49
Basic Operations 50
DYNAMIC MEASUREMENT 51
1440-DYN02-01RJ 51
Configure the Module 53
Software 55
Add the XM Module to the 56
I/O Configuration Tree 56
Profiles 57
6. Click OK 58
Configure Module 59
Properties 59
Configure the Band Properties 75
Clear to disable the alarm 78
Troubleshoot the Module 87
I/O Data Tags 91
Module-defined Data Types 92
Ch0SumHarmonics 94
Ch1SumHarmonics 95
Configuration Data Type 96
Output Data Type 101
CIP Objects 103
Identity Object 104
(Class Code 01 104
DeviceNet Object 106
(Class Code 03 106
(Class Code 04 107
Assembly Object 107
Instances 108
Instance Attributes 108
Status values change 109
Request from a Master 109
Appendix B CIP Objects 110
CIP Objects Appendix B 111
Connection Object 112
(Class ID 05H) 112
Discrete Input Point Object 114
(Class ID 08H) 114
Services 115
Analog Input Point 116
(Class ID 0A 116
Parameter Object 117
(Class ID 0F 117
Class Attributes 118
Acknowledge Handler 122
(Class ID 2BH) 122
Alarm Object 123
(Class ID 31DH) 123
Band Measurement Object 126
(Class ID 31E 126
Channel Object 128
(Class ID 31F 128
Device Mode Object 130
(Class ID 320 130
Overall Measurement 132
(Class ID 322 132
Relay Object 134
(Class ID 323 134
Spectrum Waveform 137
Measurement Object 137
(Class ID 324 137
Speed Measurement Object 144
(Class ID 325 144
Tachometer Channel Object 145
(Class ID 326 145
Transducer Object 147
(Class ID 328 147
Vector Measurement 149
(Class ID 329 149
Glossary 151
Numerics 155
Rockwell Automation Support 160
Documentation Feedback 160

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 1440-DYN02-01RJ XM Dynamic Measurement Module Manual de usuario Pagina 22

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 1440-DYN02-01RJ XM Dynamic Measurement Module