Rockwell-automation MD65 User Manual Version 2.0 Manual de usuario Pagina 113
- Pagina / 186
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Troubleshooting the Drive
10-7
10.2 Troubleshooting Tables
Use the following tables to troubleshoot the drive. If you cannot
resolve the problem using these tables, contact Reliance Electric.
10.2.1 Problem: Drive Does Not Start From Terminal
Block Start or Run Inputs
Table 10.2 – Problem: Drive Does Not Start From Terminal Block Start or Run Inputs
Possible Cause(s) Indication Corrective Action
Drive is faulted Flashing red
FAULT LED
Clear fault by using one of
the following methods:
• Press Stop
• Cycle power
• Set Fault Clear (A100) to
1 = Clear Faults
• Cycle digital input if
Digital Inx Sel (A051-
A054) is set to 7 = Clear
Fault
Incorrect programming.
• Start Source (P036) is set
to 0 = Keypad or
5 = RS485 Port.
• Digital Inx Sel (A051-A054
is set to 5 = Local and the
input is active.
None Check parameter settings.
Incorrect input wiring. See
section 6.4.1 for wiring
examples.
• 2-wire control requires
Run Forward, Run
Reverse or Jog input.
• 3-wire control requires
Start and Stop inputs
• Stop input is always
required.
None Wire inputs correctly and/or
install jumper.
Incorrect Sink/Source DIP
switch setting.
None Set switch to match wiring
scheme.
- MD65 AC Drive 1
- User Manual 1
- Version 2.0 1
- CONTENTS 3
- Contents 5
- List of Figures 7
- List of Tables 9
- MD65 AC Drive User Manual 10
- CHAPTER 1 11
- CHAPTER 2 13
- 2.3 Kits and Accessories 15
- 2.4 Storage Guidelines 16
- CHAPTER 3 17
- Mounting the Drive 19
- 3.2 Mounting the Drive 22
- CHAPTER 4 23
- 4.1 RFI Filter Grounding 24
- CHAPTER 5 25
- Match Available Power 26
- Installing Power Wiring 27
- • Line reactor 28
- • Isolation transformer 28
- • Remove MOV jumper to 28
- Drive Ratings 31
- 200-600 Volt Installations 32
- 5.7 Reflected Wave Protection 34
- 5.8 Output Disconnect 34
- CHAPTER 6 35
- • Always use copper wire 36
- Recommendations 37
- Analog Output Select 38
- 30V DC 125V AC 240V AC 38
- Resistive 3.0 A 3.0 A 3.0 A 38
- Inductive 0.5 A 0.5 A 0.5 A 38
- Installing Control Wiring 39
- 6.4.1 I/O Wiring Examples 40
- Stop-Run 41
- 6.6 Accel/Decel Selection 45
- CHAPTER 7 47
- Complete 48
- CHAPTER 8 49
- 8.1.1 Display Description 50
- • Parameter number 50
- • Parameter value 50
- • Fault code 50
- 8.1.2 LED Descriptions 50
- Table 8.2 – Key Descriptions 51
- 8.2 About Parameters 52
- Advanced (A) Parameters 53
- CHAPTER 9 55
- P036 Start Source 57
- P037 Stop Mode 58
- P038 Speed Reference 59
- P039 Accel Time 1 60
- P040 Decel Time 1 60
- P041 Reset To Defalts 61
- P042 Voltage Class 61
- 9.2 Advanced Group Parameters 62
- A055 Relay Out Sel 65
- A056 Relay Out Level 67
- Opto Out1 Sel 68
- Opto Out2 Sel 68
- A065 Analog Out Sel 71
- A066 Analog Out High 72
- A067 Accel Time 2 72
- A068 Decel Time 2 72
- A069 Internal Freq 73
- A079 Jog Accel/Decel 75
- A080 DC Brake Time 75
- A081 DC Brake Level 75
- A082 DB Resistor Sel 76
- A083 S Curve % 76
- A084 Boost Select 77
- A085 Start Boost 78
- A086 Break Voltage 78
- A087 Break Frequency 79
- A088 Maximum Voltage 79
- A089 Current Limit 1 79
- A090 Motor OL Select 79
- A091 PWM Frequency 80
- A092 Auto Rstrt Tries 80
- A093 Auto Rstrt Delay 81
- A094 Start At PowerUp 81
- A095 Reverse Disable 81
- A096 Flying Start En 82
- A097 Compensation 82
- A098 SW Current Trip 82
- A100 Fault Clear 83
- A101 Program Lock 83
- A102 Testpoint Sel 83
- A103 Comm Data Rate 84
- A104 Comm Node Addr 84
- A105 Comm Loss Action 84
- A106 Comm Loss Time 85
- A107 Comm Format 85
- A108 Language 85
- A109 Anlg Out Setpoint 86
- A110 Anlg In 0-10V Lo 86
- A112 Anlg In4-20mA Lo 87
- A113 Anlg In4-20mA Hi 87
- A114 Slip Hertz @ FLA 87
- A115 Process Time Lo 87
- A121 Stall Fault Time 89
- A122 Analog In Loss 89
- A123 10V Bipolar Enbl 90
- A124 Var PWM Disable 90
- A125 Torque Perf Mode 91
- A126 Motor NP FLA 91
- A127 Autotune 91
- A128 IR Voltage Drop 92
- A129 Flux Current Ref 92
- A130 PID Trim Hi 92
- A131 PID Trim Lo 93
- A132 PID Ref Select 93
- A133 PID Feedback Sel 93
- A134 PID Prop Gain 93
- Range: 0.0 to 999.9 sec 97
- Default: 30.0 sec 97
- A160 EM Brk Off Delay 98
- A161 EM Brk On Delay 98
- A162 MOP Reset Sel 99
- 9.3 Display Group Parameters 100
- Running Bit 0 101
- Forward Bit 1 101
- Accelerating Bit 2 101
- Decelerating Bit 3 101
- MD65 AC Drive User Manual 102
- Parameter Descriptions 103
- Receiving Data Bit 0 104
- Transmitting Data Bit 1 104
- RS485 Option Connected Bit 2 104
- CHAPTER 10 107
- Feature) 108
- Troubleshooting the Drive 109
- • Cycle power 112
- • Replace drive if fault 112
- 10.2 Troubleshooting Tables 113
- APPENDIX A 119
- CSA 22.2 121
- APPENDIX B 123
- B.2 Advanced Parameter Group 124
- Record of User Settings 125
- APPENDIX C 129
- APPENDIX D 135
- MD60 AC Drive User Manual 136
- EN61000-3-2 137
- APPENDIX E 139
- E.1 Dynamic Brake Modules 140
- Frame Model Number 141
- E.2 EMC Line Filters 142
- Accessories 143
- Description Model Number 145
- APPENDIX F 149
- Parameter Configuration 150
- RS485 (MDI) Protocol 151
- Writing (06) Reference 153
- Reading (03) Feedback 154
- Codes) 155
- APPENDIX G 157
- Cable Accessories 158
- One Permanent Peripheral 159
- Connecting an RS485 Network 160
- APPENDIX H 161
- StepLogic 162
- Using Timed Steps 162
- Using Basic Logic Functions 163
- Timer Function 164
- Counter Function 166
- Parameters 167
- PPENDIX I 169
- Trim Control 170
- PID Reference and Feedback 171
- Analog PID Reference Signals 172
- PID Deadband 173
- PID Enabled 174
- Freq Cmd 174
- PID Output 174
- PID Pre-load Value 174
- PID Pre-load Value > 0 174
- PID Gains 175
- PID Feedback 176
- PID Reference 176
- PID Set Up 177
- Numerics 179
Relacionado con productos y manuales para Equipo Rockwell-automation MD65 User Manual Version 2.0
Equipo Rockwell-automation Flex/WebPak 3000 Operator Interface Module (OIM) K Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation T8297 Trusted Output Power Distribution Unit (Diod Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation FactoryTalk Alarms and Events Quick Start Manual de usuario
(246 paginas)
(246 paginas)
Equipo Rockwell-automation T8472 Trusted TMR 120V ac Isolated Output Module Manual de usuario
(28 paginas)
(28 paginas)
Equipo Rockwell-automation CEP7-EGF CEP7 Ground Fault Accessory Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation FlexPak 3000 115 VAC Control Opt. Board M/N 917FK0 Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation T80011 Application Note Application Variable Limit Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation FlexPak Plus Auxiliary Panel 14C330, 331, 332 Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1756-EN2TSC EtherNet/IP Secure Communication User Manual de usuario
(64 paginas)
(64 paginas)
Equipo Rockwell-automation TAI16AEA 16- Channel Analogue Input Termination Mo Manual de usuario
(11 paginas)
(11 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales