Rockwell-automation 1769-SM2 Compact I/O DSI/Modbus Communication Modu Manual de usuario Pagina 25
- Pagina / 204
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installing the Module 2-3
Before installing the module, make sure its Configuration Mode Switch
is correctly set. See Configuration Methods on page 3-3 for details on
the Controller and Parameter configuration modes. Then set the
Configuration Mode Switch (SW1 in Figure 2.1
) for your application.
Figure 2.1 Configuration Mode and Single/Multi-Drive Operation Switch Locations
Setting the Configuration Mode Switch
SW1 Setting Description
CONT (Controller)
back position
Default setting—The 1769-SM2 module uses the configuration
data downloaded from the controller on power-up and when the
controller is placed in run mode.
PARAM (Parameter)
front position
The 1769-SM2 module uses its internal parameter settings to
configure the module.
(Controller
Position)
(Single
Position)
(Parameter
Position)
(Multi-Drive
Position)
Configuration
Mode Switch
(SW1)
Operating
Mode Switch
(SW2)
CONT PARAM
1X 5X
- PowerFlex 1769-SM2 1
- Compact I/O DSI/Modbus 1
- Communications Module 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- About This Manual 9
- Rockwell Automation Support 10
- P-4 About This Manual 12
- Getting Started 13
- Features 14
- Powerflex 4-Class Drives 15
- 1769-SM2 15
- Getting Started 1-5 17
- HVAC adapters 17
- Compatible Products 18
- Required Equipment 18
- Safety Precautions 19
- Quick Start 21
- Status Indicators 22
- Installing the Module 23
- Removing Power 24
- Mounting the Module 28
- Installing the Module 2-7 29
- ±0.4 mm (0.016 in.) 29
- DIN Rail Mounting 30
- Single Mode 32
- Grounding the Module 34
- To Drive 1 To Drive 2 35
- Network Cable Strain Relief 36
- Applying Power 36
- 2-16 Installing the Module 38
- Configuring the Module 39
- Configuration Tools 40
- Configuration Methods 41
- Controller Mode 41
- Before v6.30 42
- Parameter Mode 50
- DIAG PA R AM DSEL MEM SEL 51
- DIAG PARAM DSEL MEM SEL 51
- VALUE LIMITS SEL 51
- Changing the Idle Action 53
- Setting the RTU Baud Rate 55
- Selecting the RTU Format 55
- Setting the RTU Rx Delay Time 56
- Setting the RTU Tx Delay Time 56
- Resetting the Module 58
- Configuring the Module 3-21 59
- Flash Updating the Module 60
- Understanding the I/O Image 61
- Module Control Word 62
- Module Status Word 63
- Using Logic Command/Status 64
- Using Reference/Feedback 64
- Chapter 5 65
- Formatting Explicit Messages 66
- PowerFlex 4/40 Drives 82
- MicroLogix 1500 Controller 82
- CompactLogix Example Ladder 103
- Programs 103
- PowerFlex 40 Settings 104
- 1769-SM2 Settings 104
- CompactLogix Example Program 106
- Read Message (Rung 14) 109
- Write Message (Rung 17) 110
- Multi-Drive Mode 112
- PowerFlex 70 Setting 113
- 20-COMM-H Settings 114
- CH1 Drive 0: 123
- Modbus RTU operation 124
- Example Ladder Program 131
- Using RSLinx Classic 132
- Using RSNetWorx for DeviceNet 133
- Setting Up the 1769-ADN 134
- Example Program Data Table 151
- Troubleshooting 153
- MODULE Status Indicator 154
- CH1…CH3 Status Indicators 155
- Troubleshooting 9-5 157
- Viewing and Clearing Events 158
- Troubleshooting 9-7 159
- 9-8 Troubleshooting 160
- Specifications 161
- Environmental 162
- Regulatory Compliance 162
- DSI Cable Requirements 162
- Module Parameters 163
- B-2 Module Parameters 164
- Module Parameters B-3 165
- B-4 Module Parameters 166
- Module Parameters B-5 167
- B-6 Module Parameters 168
- Module Parameters B-7 169
- B-8 Module Parameters 170
- CIP/DSI Objects 171
- Supported Data Types 172
- CIP Identity Object 173
- CIP Parameter Object 174
- Instance Attributes 175
- (Continued) 175
- Services 176
- DSI Device Object 177
- DSI Device Object (Continued) 178
- DSI Parameter Object 180
- Descriptor Attributes 182
- CIP/DSI Objects C-13 183
- DSI Fault Object 184
- DSI Fault Object (Continued) 185
- DSI Diagnostic Object 186
- C-18 CIP/DSI Objects 188
- Command/Status Words 189
- Logic Status Word 190
- Glossary 191
- F Flash Update 192
- I Idle Action 193
- L Logic Command/Logic Status 193
- N NVS (Non-Volatile Storage) 193
- O Objects 193
- R Reference/Feedback 194
- S Scanner 195
- Z Zero Data 195
- Glossary-6 196
Relacionado con productos y manuales para Equipo Rockwell-automation 1769-SM2 Compact I/O DSI/Modbus Communication Modu
Equipo Rockwell-automation 1794-AENTR_AENTRXT FLEX I/O Dual Port EtherNet/IP Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1764-28BXB MICROLOGIX 1500 PROG. CONTROLLER BASE U Manual de usuario
(115 paginas)
(115 paginas)
Equipo Rockwell-automation 1792D-8BT8PE ArmorBlock MaXum 8 In/8 Out Module wi Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1785-Lx0E Ethernet PLC-5 Programmable Controllers Manual de usuario
(28 paginas)
(28 paginas)
Equipo Rockwell-automation 1771-IXHR , D17716.5.80 HIGH RESOL.THERMOCOUPLE Manual de usuario
(60 paginas)
(60 paginas)
Equipo Rockwell-automation 1751 SynchLink 4-Port Splitter Block Installation Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1757-SWKIT400 ProcessLogix R400.0 Server Installat Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 1769-IF4XOF2 Compact 8-Bit Low Resolution Analog I Manual de usuario
(104 paginas)
(104 paginas)
Equipo Rockwell-automation 1784-PM02AE-TP0 2 Axis Servo Card Termination Pane Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1794-ID2/B INSTALL INSTR 24v FLEX I/O 2 CHANNEL In Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1753-IF8XOF4 GuardPLC 1753-IF8XOF4 Analog I/O Modu Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1758-RTU202 DataSite Software User Manual FRN 1.2 Manual de usuario
(348 paginas)
(348 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales