Rockwell-automation 22-COMM-E EtherNet/IP Adapter Manual de usuario Pagina 65
- Pagina / 166
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using Multi-Drive Mode 7-5
The following parameters must be set in the daisy-chained drives:
Note that the RS-485 network is fixed at 19.2K baud, 8 data bits, no
parity, and 1 stop bit.
Important: Parameters A105 - [Comm Loss Action] and A106 -
[Comm Loss Time] in the daisy-chained drives are still
used in Multi-Drive mode. If the RS-485 cable is
disconnected or broken, the disconnected drive(s) will take
the corresponding Comm Loss Action(s). On the EtherNet/
IP side, Parameters 18 - [Comm Flt Action] and 19 -
[Idle Flt Action] in the 22-COMM-E determine the action
taken for ALL of the drives on the Multi-Drive node.
The following Multi-Drive parameters must be set in the 22-COMM-E:
After setting the 22-COMM-E parameters, set the Operating Mode
Switch (SW1) from Single drive operation to Multi-Drive operation (set
to ON position), and reset the adapter or cycle power. Refer to Chapter
2,
Setting Operating Mode and Web Pages Switches.
Important: 22-COMM-E parameters can be set using a DSI peripheral
(HIM, DriveExplorer with 22-SCM-232, etc.) ONLY when
the Operating Mode Switch is in the Single mode position
(SW1 = OFF).
Configuring the RS-485 Network
Parameter Value
P36 - [Start Source] 5 (Comm Port)
P38 - [Speed Reference] 5 (Comm Port)
A103 - [Comm Data Rate] 4 (“19.2K”)
A104 - [Comm Node Addr] 1-247 (must be unique)
A107 - [Comm Format] 0 (“RTU 8-N-1”)
Parameter Value
22 - [DSI I/O Cfg] 0 = Drive 0 connected
1 = Drives 0-1 connected
2 = Drives 0-2 connected
3 = Drives 0-3 connected
4 = Drives 0-4 connected
24 - [Drv 0 Addr] = Parameter A104 - [Comm Node Address] in Drive 0
25 - [Drv 1 Addr] = Parameter A104 - [Comm Node Address] in Drive 1
26 - [Drv 2 Addr] = Parameter A104 - [Comm Node Address] in Drive 2
27 - [Drv 3 Addr] = Parameter A104 - [Comm Node Address] in Drive 3
28 - [Drv 4 Addr] = Parameter A104 - [Comm Node Address] in Drive 4
- EtherNet/IP 1
- Important User Information 2
- Summary of Changes 3
- S-ii Summary of Changes 4
- Table of Contents 5
- Chapter 5 Using I/O Messaging 6
- Chapter 8 Troubleshooting 6
- About This Manual 9
- Rockwell Automation Support 10
- Technical Product Assistance 11
- P-4 About This Manual 12
- Getting Started 13
- Features 14
- Compatible Products 15
- Required Equipment 15
- Safety Precautions 16
- Quick Start 17
- Modes of Operation 18
- Bottom side 18
- Installing the Adapter 19
- Item Description 22
- DSI Connector 22
- Ethernet cable 22
- Installing the Adapter 2-5 23
- Applying Power 24
- Commissioning the Adapter 24
- Configuring the Adapter 25
- Using the HIM 26
- Using BOOTP 27
- To disable the BOOTP feature 29
- VALU E LIMITS SEL X 30
- VALUE LIMITS SEL X 30
- Setting the Data Rate 31
- Setting the I/O Configuration 31
- Setting a Fault Action 32
- To change the fault action 33
- Setting Web Features Access 34
- Resetting the Adapter 35
- 3-12 Configuring the Adapter 36
- Chapter 4 37
- Saving the Configuration 43
- Using I/O Messaging 45
- Understanding the I/O Image 46
- Using Logic Command/Status 46
- Using Reference/Feedback 47
- Example Ladder Logic Program 47
- 5-6 Using I/O Messaging 50
- Using Explicit Messaging 51
- Using Explicit Messaging 6-3 53
- Message Formats 55
- Ladder Logic Rungs 55
- Source and Destination Data 55
- Example Message Format 56
- Example Ladder Logic Rung 57
- Example Destination Data 57
- Example Source Data 59
- 6-10 Using Explicit Messaging 60
- Using Multi-Drive Mode 61
- System Wiring 63
- ControlLogix Example 67
- Main Routine 68
- Using Multi-Drive Mode 7-9 69
- 7-10 Using Multi-Drive Mode 70
- Using Multi-Drive Mode 7-11 71
- 7-12 Using Multi-Drive Mode 72
- Using Multi-Drive Mode 7-13 73
- 7-14 Using Multi-Drive Mode 74
- Using Multi-Drive Mode 7-15 75
- 7-16 Using Multi-Drive Mode 76
- Using Multi-Drive Mode 7-17 77
- 7-18 Using Multi-Drive Mode 78
- Using Multi-Drive Mode 7-19 79
- Additional Information 82
- Troubleshooting 83
- PORT Status Indicator 84
- MOD Status Indicator 85
- Net A Status Indicator 86
- Net B Status Indicator 87
- 8-6 Troubleshooting 88
- Troubleshooting 8-7 89
- (version 3.01 or higher) 89
- Viewing and Clearing Events 90
- Troubleshooting 8-9 91
- 8-10 Troubleshooting 92
- Chapter 9 93
- TCP/IP Configuration Web Page 99
- Information Description 102
- DSI Device Information Pages 103
- Specifications 105
- Environmental 106
- Regulatory Compliance 106
- Adapter Parameters 107
- B-2 Adapter Parameters 108
- Adapter Parameters B-3 109
- B-4 Adapter Parameters 110
- 01234576 111
- B-6 Adapter Parameters 112
- EtherNet/IP Objects 113
- Identity Object 114
- Identity Object (Continued) 115
- Assembly Object 116
- Assembly Object (Continued) 117
- Register Object 118
- Register Object (Continued) 119
- Parameter Object 121
- Parameter Object (Continued) 122
- Parameter Group Object 125
- Instance Attributes 126
- Services 126
- (Continued) 126
- PCCC Object 127
- PCCC Object (Continued) 128
- DPI Device Object 133
- DPI Device Object (Continued) 134
- DPI Parameter Object 136
- Descriptor Attributes 138
- Formulas for Converting 139
- Common Services 139
- Object Specific Services 139
- DPI Fault Object 140
- DPI Fault Object (Continued) 141
- DPI Diagnostic Object 142
- TCP/IP Interface Object 144
- Ethernet Link Object 146
- C-36 EtherNet/IP Objects 148
- Logic Command/Status Words 149
- Logic Status Word 150
- Glossary 151
- D Data Rate 152
- F Fault Action 153
- G Gateway 154
- H Hardware Address 154
- I I/O Data 155
- L Logic Command/Logic Status 156
- N NVS (Non-Volatile Storage) 156
- R Reference/Feedback 156
- S Scanner 157
- Z Zero Data 158
- I-6 Index 164
Relacionado con productos y manuales para Equipo Rockwell-automation 22-COMM-E EtherNet/IP Adapter
Equipo Rockwell-automation 140U N-Frame CB Alarm Switch and Alarm Auxiliary S Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1203-SSS Smart Self-powered Serial Converter Manual de usuario
(60 paginas)
(60 paginas)
Equipo Rockwell-automation 42EF RightSight DeviceNet Photoelectric Sensors Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 20P PowerFlex DC Drive - Frame D Field Fuse Holder Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 20P PowerFlex DC Drive - Frame A AC CurrentTransdu Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 42DRC-5400 Retroreflective/Diffuse PHOTOSWITCH Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 42EF RightSight Photoelectric Sensors with Teach F Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 20Y PowerFlex 700AFE Spare Parts Installation Inst Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 140U Q and M-Frame Circuit Breakers Instruction Le Manual de usuario
(5 paginas)
(5 paginas)
Equipo Rockwell-automation 20P PowerFlex DC Drive - Frame A Switching Power S Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 140EX-KE2_KE3_KE5 Molded Case Circuit Breaker Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 140G-M-RMX_NVMx_RVMx_N7_N8 Rot Oper Mech w/ Ext Ha Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 20P PowerFlex DC Drive - Frame D Field Circuit Boa Manual de usuario
(6 paginas)
(6 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales