Rockwell-automation 25B PowerFlex 525 Embedded EtherNet/IP Adapter Manual de usuario Pagina 112
- Pagina / 166
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
112 Rockwell Automation Publication 520COM-UM001B-EN-E - March 2013
Chapter 8 Troubleshooting
ENET Status Indicator
This green color LED indicates the status of the adapter’s network connection as
shown in the table below.
LINK Status Indicator
This green LED indicates the status of the adapter transmitting on the network
as shown in the table below.
Viewing Adapter Diagnostic
Items
If you encounter unexpected communications problems, the adapter’s diagnostic
items may help you or Rockwell Automation personnel troubleshoot the
problem. The diagnostic parameters for the embedded EtherNet/IP adapter can
be viewed using the PowerFlex 22-HIM-A3/-C2S HIM.
Status Cause Corrective Actions
Off There is no network link (unplugged
Ethernet cable), the network configuration
is invalid or a duplicate IP address error has
been detected.
• Apply power to the drive.
• Securely connect the adapter to the network using an
Ethernet cable. Also, make sure the Ethernet cable is
correctly connected to the Ethernet connector.
• Set a unique IP address using the adapter switches, a
BOOTP server, or by disabling BOOTP and using adapter
parameters.
Flashing The adapter is properly connected to the
network but drive is not controlled through
Ethernet.
• Place the controller in RUN mode, or apply power to the
peer device that will send I/O.
• Program the controller or peer device to recognize and
transmit I/O or make a messaging connection to the
adapter.
• Configure the adapter for the program in the controller or
the I/O from the peer device.
Steady The adapter is properly connected to the
network and drive is controlled through
Ethernet.
No action required.
Status Cause Corrective Actions
Off There is no network link (unplugged
Ethernet cable) or a duplicate IP address
error has been detected.
• Apply power to the drive.
• Securely connect the adapter to the network using an
Ethernet cable. Also, make sure the Ethernet cable is
correctly connected to the Ethernet connector.
Flashing The adapter is properly connected to the
network and drive is transmitting data on
Ethernet.
No action required.
Steady The adapter is properly connected to the
network but drive is not transmitting data
on Ethernet.
• Set a unique IP address using the adapter switches, a
BOOTP server, or by disabling BOOTP and using adapter
parameters.
• Configure the adapter to use a unique IP address and
cycle power.
• Check the IP address in the adapter and scanner, and
verify that the controller can communicate with the
adapter.
• Ping the adapter.
Normal condition if the adapter is idle.
Embedded EtherNet/IP Adapter Diagnostic Parameters
No. Name Description
F681 Comm Sts - DSI Displays the status of the RS485 serial (DSI) port to the drive.
F682 Comm Sts - Opt Displays the status of the internal communication to the drive.
F683 Com Sts-Emb Enet Displays the status of the embedded EtherNet/IP interface to the drive.
F684 EN Addr Src Displays the network configuration source currently used by the embedded EtherNet/IP
interface.
F685 EN Rate Act Displays the network data rate currently used by the embedded EtherNet/IP interface.
F686 DSI I/O Act Displays the drives that are active in Multi-drive mode.
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Logic Command/Status Words: 7
- PowerFlex 525 Drives 7
- Overview 9
- Preface Overview 10
- Getting Started 11
- Features 12
- Compatible Products 12
- Required Equipment 12
- User-Supplied Equipment 13
- Safety Precautions 14
- Quick Start 14
- ENET LINK 15
- EtherNet/IP 15
- Chapter 1 Getting Started 16
- Setting Up the Adapter 17
- Setting the IP Address 18
- Connecting the Adapter to 18
- Startup Status Indication 19
- Commissioning the Adapter 21
- Configuring the Adapter 23
- Using the PowerFlex 4-Class 25
- HIM to Access Parameters 25
- Using BOOTP 26
- Subnet Mask, and Gateway 29
- Setting the Data Rate 30
- Using Master-Slave Hierarchy 31
- Setting a Fault Action 33
- Resetting the Adapter 34
- Viewing the Adapter Status 34
- Using Parameters 34
- Configuring the I/O 37
- CompactLogix Example 38
- 1 (Front)1 (Front)1 (Front) 38
- 2 (Rear) 38
- 00:00:BC:2E:69:F6 38
- Configuring the I/O Chapter 4 39
- Chapter 4 Configuring the I/O 40
- Controller Input Tags 45
- Controller Output Tags 45
- Differences Found Screen 48
- ADC and Logix Memory 52
- Monitoring the ADC Progress 53
- Input Image Controller Tags 58
- Output Image Controller Tags 58
- Limitations in Using 60
- MicroLogix 1100/1400 60
- Using the I/O 61
- Using Logic Command/Status 62
- Using Reference/Feedback 63
- Using Datalinks 63
- Example Ladder Logic 64
- Program Information 64
- Feedback 65
- Controller Tags 66
- Program Tags 67
- Reference 68
- Using Explicit Messaging 69
- Performing Explicit 70
- CompactLogix Examples 70
- Parameter 71
- Parameters 74
- Write Multiple Messaging 79
- 520-UM001 80
- Using Multi-Drive Mode 83
- System Wiring 85
- Understanding the I/O Image 85
- Configuring the RS-485 86
- Using Multi-Drive Add-On 87
- Multi-Drive Ladder Logic 97
- Program for Generic Profile 97
- CompactLogix Example Using 99
- Generic Profile 99
- Main Routine 100
- Drive 0...4 Control Routines 101
- Drive 0 Control Routine 102
- Drive 1 Control Routine 103
- Drive 2 Control Routine 104
- Drive 3 Control Routine 105
- Drive 4 Control Routine 106
- Multi-Drive Mode Explicit 107
- Messaging 107
- Additional Information 108
- Troubleshooting 111
- ENET Status Indicator 112
- LINK Status Indicator 112
- Viewing Adapter Diagnostic 112
- Viewing and Clearing Events 114
- Adapter Events 115
- Chapter 8 Troubleshooting 116
- Specifications 117
- Appendix A Specifications 118
- Adapter Parameters 119
- Appendix B Adapter Parameters 124
- EtherNet/IP Objects 125
- Identity Object 126
- Instance Attributes 127
- Assembly Object 128
- Register Object 129
- Instances (Multi-Drive) 130
- Class Attributes 131
- Parameter Object 132
- PCCC Object 135
- DPI Device Object 138
- Instance Attribute 140
- DPI Parameter Object 141
- on page 146 143
- Descriptor Attributes 144
- Formulas for Converting 146
- Common Services 146
- Object Specific Services 146
- DPI Fault Object 147
- TCP/IP Interface Object 149
- Ethernet Link Object 151
- Appendix D 153
- Logic Command Word 153
- Logic Status Word 154
- Position Bit Definitions 155
- Glossary 157
- Rockwell Automation Support 166
- Documentation Feedback 166
Relacionado con productos y manuales para Equipo Rockwell-automation 25B PowerFlex 525 Embedded EtherNet/IP Adapter
(6 paginas)
(1 paginas)
(2 paginas)
Equipo Rockwell-automation 193x-EExxP E1 PLUS Overload Relay Application and Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 20G PowerFlex 750-Series EMC Plate and Cores - Fra Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation 194RC-Nxxxx NFPA 79 Compliant Cable Operated Disco Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 20-750-xxxx Network Communication Option Card (for Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales