Rockwell-automation 25B PowerFlex 525 Embedded EtherNet/IP Adapter Manual de usuario Pagina 119
- Pagina / 166
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication 520COM-UM001B-EN-E - March 2013 119
Appendix B
Adapter Parameters
Appendix B provides information about the parameters used to configure the
embedded EtherNet/IP adapter.
Parameter List
The parameters are displayed in a Numbered List view order.
Topic Page
Parameter List 119
Parameter
No. Name and Description Details
C121 [Comm Write Mode]
Saves parameter values in active drive memory (RAM) or in
drive non-volatile memory (EEPROM).
Important: Parameter values set prior to setting 1 “RAM only”
are saved in RAM.
Default: 0 = Save
Values: 0 = Save
1 = RAM only
Typ e: Re ad/Write
Reset Required:
C122 [Cmd Stat Select]
Selects velocity-specific or position/fibers-specific Command
and Status Word bit definitions for use over a communication
network.
This parameter cannot be changed when an I/O connection is
established through the communication adapter or the drive’s
embedded EtherNet/IP port.
Default: 0 = Velocity
Values: 0 = Velocity
1 = Position
Typ e: Re ad/Write
Reset Required: Yes
C123 [RS485 Data Rate]
Sets the communications baud rate (bits/second) for the RS485
port. A reset or power cycle is required after selection is made.
Default: 3 = 9600
Values: 0 = 1200
1 = 2400
2 = 4800
3 = 9600
4 = 19,200
5 = 38,400
Typ e: Re ad/Write
Reset Required: Yes
C124 [RS485 Node Addr]
Sets the Modbus drive node number (address) for the RS485
port if using a network connection. A reset or power cycle is
required after selection is made.
Default: 100
Minimum: 1
Maximum: 247
Typ e: Re ad/Write
Reset Required: Yes
C125 [Comm Loss Action]
Sets the drive's response to a loss of connection or excessive
communication errors on the RS485 port.
Default: 0 = Fault
Values: 0 = Fault
1 = Coast Stop
2 = Stop
3 = Continu Last
Typ e: Re ad/Write
Reset Required: No
C126 [Comm Loss Time]
Sets the time that the drive remains in communication loss with
the RS485 port before taking the action specified in C125
[Comm Loss Action].
Important: This setting is effective only if I/O that controls the
drive is transmitted through the RS485 port.
Default: 5.0 s
Minimum: 0.1 s
Maximum: 60.0 s
Typ e: Re ad/Write
Reset Required: No
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Logic Command/Status Words: 7
- PowerFlex 525 Drives 7
- Overview 9
- Preface Overview 10
- Getting Started 11
- Features 12
- Compatible Products 12
- Required Equipment 12
- User-Supplied Equipment 13
- Safety Precautions 14
- Quick Start 14
- ENET LINK 15
- EtherNet/IP 15
- Chapter 1 Getting Started 16
- Setting Up the Adapter 17
- Setting the IP Address 18
- Connecting the Adapter to 18
- Startup Status Indication 19
- Commissioning the Adapter 21
- Configuring the Adapter 23
- Using the PowerFlex 4-Class 25
- HIM to Access Parameters 25
- Using BOOTP 26
- Subnet Mask, and Gateway 29
- Setting the Data Rate 30
- Using Master-Slave Hierarchy 31
- Setting a Fault Action 33
- Resetting the Adapter 34
- Viewing the Adapter Status 34
- Using Parameters 34
- Configuring the I/O 37
- CompactLogix Example 38
- 1 (Front)1 (Front)1 (Front) 38
- 2 (Rear) 38
- 00:00:BC:2E:69:F6 38
- Configuring the I/O Chapter 4 39
- Chapter 4 Configuring the I/O 40
- Controller Input Tags 45
- Controller Output Tags 45
- Differences Found Screen 48
- ADC and Logix Memory 52
- Monitoring the ADC Progress 53
- Input Image Controller Tags 58
- Output Image Controller Tags 58
- Limitations in Using 60
- MicroLogix 1100/1400 60
- Using the I/O 61
- Using Logic Command/Status 62
- Using Reference/Feedback 63
- Using Datalinks 63
- Example Ladder Logic 64
- Program Information 64
- Feedback 65
- Controller Tags 66
- Program Tags 67
- Reference 68
- Using Explicit Messaging 69
- Performing Explicit 70
- CompactLogix Examples 70
- Parameter 71
- Parameters 74
- Write Multiple Messaging 79
- 520-UM001 80
- Using Multi-Drive Mode 83
- System Wiring 85
- Understanding the I/O Image 85
- Configuring the RS-485 86
- Using Multi-Drive Add-On 87
- Multi-Drive Ladder Logic 97
- Program for Generic Profile 97
- CompactLogix Example Using 99
- Generic Profile 99
- Main Routine 100
- Drive 0...4 Control Routines 101
- Drive 0 Control Routine 102
- Drive 1 Control Routine 103
- Drive 2 Control Routine 104
- Drive 3 Control Routine 105
- Drive 4 Control Routine 106
- Multi-Drive Mode Explicit 107
- Messaging 107
- Additional Information 108
- Troubleshooting 111
- ENET Status Indicator 112
- LINK Status Indicator 112
- Viewing Adapter Diagnostic 112
- Viewing and Clearing Events 114
- Adapter Events 115
- Chapter 8 Troubleshooting 116
- Specifications 117
- Appendix A Specifications 118
- Adapter Parameters 119
- Appendix B Adapter Parameters 124
- EtherNet/IP Objects 125
- Identity Object 126
- Instance Attributes 127
- Assembly Object 128
- Register Object 129
- Instances (Multi-Drive) 130
- Class Attributes 131
- Parameter Object 132
- PCCC Object 135
- DPI Device Object 138
- Instance Attribute 140
- DPI Parameter Object 141
- on page 146 143
- Descriptor Attributes 144
- Formulas for Converting 146
- Common Services 146
- Object Specific Services 146
- DPI Fault Object 147
- TCP/IP Interface Object 149
- Ethernet Link Object 151
- Appendix D 153
- Logic Command Word 153
- Logic Status Word 154
- Position Bit Definitions 155
- Glossary 157
- Rockwell Automation Support 166
- Documentation Feedback 166
Relacionado con productos y manuales para Equipo Rockwell-automation 25B PowerFlex 525 Embedded EtherNet/IP Adapter
(6 paginas)
(1 paginas)
(2 paginas)
Equipo Rockwell-automation 193x-EExxP E1 PLUS Overload Relay Application and Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 20G PowerFlex 750-Series EMC Plate and Cores - Fra Manual de usuario
(10 paginas)
(10 paginas)
Equipo Rockwell-automation 194RC-Nxxxx NFPA 79 Compliant Cable Operated Disco Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 20-750-xxxx Network Communication Option Card (for Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.592 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales