Rockwell-automation 1503VC IntelliVAC Plus Contactor Control Module Manual de usuario Pagina 168
- Pagina / 387
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Troubleshooting 10-5
1503-UM054C-EN-P – June 2013
Table 10.B - IE Operations Troubleshooting Procedures (cont.)
Plus Status
LED Color
State Condition/Possible Cause Corrective Action
Green
2 pulses
Warning
RTC failure
RTC not responding
1. Replace the IntelliVAC Plus module.
Green
3 pulses
Warning
Line undervoltage
Input mains v oltage is too low
Input mains v oltage is too low on other
MC units
Check the mains input line and v erify that it remains
greater than 95Vrms to allow a contactor to be
closed. If the input voltage remains less than 95Vrms
then improvements to the source must be made.
This warning can be from any of the IntelliVAC MC
units in an MC system. Perform the same checks for
those units as well.
Green
4 pulses
Warning
Line overvoltage
Input mains v oltage is too high
Input mains voltage is too high on other
MC units
Check the mains input line and v erify that it remains
lower than 265Vrms to prevent damage to the
IntelliVAC Plus module.
This warning can be from any of the IntelliVAC MC
units in an MC system. Perform the same checks for
those units as well.
Green
5 pulses
Warning
Extended close time
Faulty contactor mechanics
Faulty contactor coil
Faulty contactor coil on other MC units
Check the mechanical condition of the contactor as
this warning is an indication that the moving
mechanisms of the contactor are beginning to wear.
Check the resistance of the contactor coil and
compare it to the values.
This warning can be from any of the IntelliVAC MC
units in an MC sy stem. Perform the same checks for
those units as well.
Green
6 pulses
Warning
DeviceNet power loss
1. DeviceNet connection faulty
2. DeviceNet input voltage too low
Check that the DeviceNet connections to the
IntelliVAC Plus are correct and that the DeviceNet
source connections are correct as well.
Check that the DeviceNet input voltage at terminals
TB1-5,1 is greater than the minimum voltage as
defined in the Electrical Specification
Green
7 pulses
Warning
MC Altitude setting
Incorrect altitude DIP sw itch setting
The altitude setting defined by the DIP switches
(SW1-1,2,3) on the Basic module is not consistently
set on all units in an MC sy stem. Adjust the DIP
switches on all units to the same altitude setting.
- IntelliVAC™ Plus Contactor 1
- Control Module 1
- Important User Information 2
- Table of Contents 3
- Chapter 6 6
- Chapter 7 Communications 6
- Chapter 8 Configurations 6
- Chapter 9 DeviceLogix 7
- Product Description 11
- Description 12
- TOP VIEW 14
- IntelliVAC Features 15
- IntelliVAC Base Module 15
- Versions 15
- I M P O R T A N T 16
- Specifications (cont.) 19
- Receiving and Storage 22
- 2-2 Receiving and Storage 23
- Installation 24
- 3-2 Installation 25
- Installation 3-3 26
- Description of Features 28
- Contactor Close 31
- Re-Closing Control 32
- Features 32
- Delayed Restart (General) 33
- Temporary Jog Function 34
- Table 4.D – Event Log Data 36
- Time Stamp 36
- 37
- Valid Data Range 41
- Altitude/Air Pressure 43
- Compensation (400A 43
- Contactors) 43
- RS NetWorx Software 48
- Dual Power Supply Operation 48
- Power Fail Operation 48
- Status Display Items 49
- Contactor Fails to Pick Up 54
- IE Module/Network 59
- Status LEDs 59
- DeviceNet Power Loss 64
- Network Status 67
- (DeviceNet) 67
- (cont.) 68
- Output LEDs 75
- Input LEDs 75
- IntelliVAC Plus Basic Wiring 76
- Ground Connection 77
- CONTACTOR INTERFACE 78
- 11 128 9 105 6 72 3 41 78
- EX. CAP 78
- Wiring Guidelines 79
- Electrically Held 79
- Contactors 79
- Three-Wire Control 80
- Contactors (cont.) 81
- Mechanical Latch 82
- Capacitor Trip 83
- Wiring 88
- 6-2 Wiring (MC) 89
- Wiring (MC) 6-3 90
- 6-4 Wiring (MC) 91
- Wiring (MC) 6-5 92
- 6-6 Wiring (MC) 93
- Wiring (MC) 6-7 94
- 6-8 Wiring (MC) 95
- Incomplete Sequence Timer 96
- Transition Timer 96
- 6-10 Wiring (MC) 97
- 6-12 Wiring (MC) 99
- Communications 100
- DeviceNet 101
- DeviceNet MACID 102
- 7-4 Communications 103
- Communications 7-5 104
- 7-6 Communications 105
- Configuration/Programming 106
- Contactor Drop 107
- Out Time 107
- Table 8.C – Contactor Type 108
- Table 8.G – Future Use 110
- TERMINATION 111
- Programming 112
- Power down the unit 113
- Select “send file” 117
- Select “send” 117
- IE/IB Firmware Revisions 122
- DeviceLogix 124
- 9-2 DeviceLogix 125
- What is DeviceLogix 126
- Inputs and Outputs 126
- Input and Output Bits 126
- Local Function Block Logic 127
- DeviceLogix Operating Modes 128
- 9-6 DeviceLogix 129
- DeviceLogix 9-7 130
- 9-8 DeviceLogix 131
- DeviceLogix 9-9 132
- 9-10 DeviceLogix 133
- 9-12 DeviceLogix 135
- DeviceLogix 9-13 136
- Pulse Timer 138
- On Delay Timer 139
- Go Online 144
- Entering Logic Into 146
- The Editor 146
- Assume Data Available 147
- Figure 9.15 – Forcing 149
- Table 9.I – Input Forcing 149
- Table 9.J – Output Forcing 150
- 9-28 DeviceLogix 151
- Network Boolean Inputs 157
- Output bits/tags 158
- Hardware Boolean Outputs 158
- Network Boolean Outputs 158
- Simple example 160
- DeviceLogix 9-39 162
- 9-40 DeviceLogix 163
- Troubleshooting 164
- Status LED 167
- 2 pulses 169
- 5 pulses 169
- 6 pulses 169
- 7 pulses 170
- 8 pulses 170
- Segment LED Display 172
- Appendix A 174
- Fuse Protection 174
- A-2 Fuse Protection 175
- Parameters 176
- B-4 Parameters 179
- Parameters B-5 180
- B-6 Parameters 181
- Parameters B-7 182
- B-8 Parameters 183
- Parameters B-9 184
- B-10 Parameters 185
- Parameters B-11 186
- B-12 Parameters 187
- Parameters B-13 188
- B-14 Parameters 189
- Parameters B-15 190
- B-16 Parameters 191
- Parameters B-17 192
- B-18 Parameters 193
- Parameters B-19 194
- B-20 Parameters 195
- Parameters B-21 196
- B-22 Parameters 197
- Parameters B-23 198
- B-24 Parameters 199
- Parameters B-25 200
- B-26 Parameters 201
- Parameters B-27 202
- B-28 Parameters 203
- Parameters B-29 204
- B-30 Parameters 205
- Parameters B-31 206
- B-32 Parameters 207
- Table B.7 – Control Masks 211
- Parameters B-37 212
- B-42 Parameters 217
- Parameters B-55 230
- B-56 Parameters 231
- Parameters B-57 232
- B-58 Parameters 233
- Parameters B-59 234
- B-60 Parameters 235
- Parameters B-61 236
- B-62 Parameters 237
- Parameters B-63 238
- B-64 Parameters 239
- Parameters B-69 244
- B-74 Parameters 249
- Parameters B-75 250
- B-76 Parameters 251
- Parameters B-77 252
- B-78 Parameters 253
- Parameters B-79 254
- B-80 Parameters 255
- Parameters B-81 256
- B-82 Parameters 257
- Parameters B-83 258
- B-84 Parameters 259
- Parameters B-85 260
- B-86 Parameters 261
- Parameters B-87 262
- B-88 Parameters 263
- Parameters B-89 264
- B-90 Parameters 265
- Parameters B-91 266
- B-92 Parameters 267
- Parameters B-93 268
- B-94 Parameters 269
- Parameters B-95 270
- B-96 Parameters 271
- Parameters B-97 272
- B-98 Parameters 273
- Parameters B-99 274
- B-100 Parameters 275
- Parameters B-101 276
- B-102 Parameters 277
- Parameters B-103 278
- B-104 Parameters 279
- Parameters B-105 280
- B-106 Parameters 281
- Parameters B-107 282
- B-108 Parameters 283
- Parameters B-109 284
- B-110 Parameters 285
- Parameters B-111 286
- B-112 Parameters 287
- B-114 Parameters 289
- Parameters B-115 290
- B-116 Parameters 291
- Parameters B-117 292
- B-118 Parameters 293
- Parameters B-119 294
- B-120 Parameters 295
- Parameters B-121 296
- B-122 Parameters 297
- B-128 Parameters 303
- Parameters B-129 304
- Parameters B-135 310
- B-136 Parameters 311
- Parameters B-137 312
- B-138 Parameters 313
- Parameters B-139 314
- B-140 Parameters 315
- Parameters B-141 316
- B-142 Parameters 317
- Parameters B-143 318
- B-144 Parameters 319
- Parameters B-145 320
- B-146 Parameters 321
- Parameters B-147 322
- B-148 Parameters 323
- Parameters B-149 324
- B-150 Parameters 325
- Parameters B-151 326
- B-152 Parameters 327
- Parameters B-153 328
- B-154 Parameters 329
- Parameters B-155 330
- B-156 Parameters 331
- Parameters B-157 332
- B-158 Parameters 333
- Parameters B-159 334
- B-160 Parameters 335
- Parameters B-161 336
- B-162 Parameters 337
- Parameters B-163 338
- B-164 Parameters 339
- Parameters B-165 340
- B-166 Parameters 341
- B-168 Parameters 343
- Parameters B-169 344
- B-170 Parameters 345
- Parameters B-171 346
- B-172 Parameters 347
- B-178 Parameters 353
- Parameters B-179 354
- B-182 Parameters 357
- B-184 Parameters 359
- Parameters B-185 360
- B-186 Parameters 361
- Appendix C 362
- Maintenance 362
- Battery Holder 363
- Appendix D 364
- Spare Parts 364
- D-2 Spare Parts 365
- Appendix E 366
- DeviceNet Information 366
- DeviceNet Object 367
- Explicit Connection 369
- Parameter Object 370
- Common Service 371
- IB OutA=close coil command 372
- IB OutB=open coil command 372
- 1503-UM054C-EN-P – June 2013 373
- Important Notes: 374
- DNI (IE) Object 374
- Table E.26 - Common Services 379
- Class Attributes: None 380
- Number of Instances: 1 380
- Data Table Layout 381
- E-18 DeviceNet Information 383
- Appendix F 384
- IntelliVAC Plus Firmware 384
- Medium Voltage Products 387
Relacionado con productos y manuales para Equipo Rockwell-automation 1503VC IntelliVAC Plus Contactor Control Module
Equipo Rockwell-automation 14885P KwikLink Lite, Field Network Pressure-Welde Manual de usuario
(3 paginas)
(3 paginas)
Equipo Rockwell-automation 1492-CM1771-LA002 Analog I/O Conversion Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1494V-DS200_DSX200 Disconnect (200A) Quick Install Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1492-CM800-LD015 Field Wire Conv. Module for Modic Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1492 Accessory Modules For Circuit Breakers Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1336E IMPACT Adjustable Frequency AC Drive User Ma Manual de usuario
(419 paginas)
(419 paginas)
Equipo Rockwell-automation 1606-XLS240-UPS_UPSD_UPSE DC-UPS Uninterruptible P Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1492-PLTKIT Series E plotter using the USB Port Fi Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales