Rockwell-automation 1503VC IntelliVAC Plus Contactor Control Module Manual de usuario Pagina 173
- Pagina / 387
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
10-10 Troubleshooting
1503-UM054C-EN-P – June 2013
Table 10.D – MC Operational Troubleshooting Procedures
7-Segment
Display
State Condition/Possible Cause Corrective Action
Off
Normal
No input power on the mains input
Input mains v oltage low
Input mains connections faulty
Failed internal fuse
Check that the mains input voltage, on the IntelliVAC
MC unit is within the operating voltage range defined
in the Electrical Specification.
Check the connections to the mains input voltage.
If the mains input voltage is present, check the
internal fuse.
Off
Fault
Invalid MC address selected
MC address is invalid
Set the MC address to either 2,3,4 or 5. Addresses
0,1,6 or 7 are inv alid and will not be displayed on the
7-segment LED display of the IntelliVAC MC module.
DeviceNet Troubleshooting Procedures
The following table identifies possible causes and corrective actions
when troubleshooting IE related faults using the DeviceNet Network
Status LED.
Table 10.E – DeviceNet Troubleshooting Procedures
Network
Status LED
Color
State Condition/Possible Cause Corrective Action
Off
Normal
There is no pow er from the mains input
or from DeviceNet.
1. Low input mains voltage
2. Input mains connections faulty
3. DeviceNet connections faulty
4. No/low DeviceNet input power
5. No/low DeviceNet input power and
mains input power present
Check that the mains input voltage is within the
operating voltage range defined in the Electrical
Specification.
Check the connections to the mains input voltage.
Check the DeviceNet connections.
Check that the DeviceNet input power (if present) is
within the operating voltage range defined in the
Electrical specification.
If there is no DeviceNet power and the mains input
voltage is present, check the internal fuse.
Green
flashing
Warning
Determining network baud rate
1. IntelliVAC Plus is on-line but not
allocated to a master.
Check DeviceNet master and its scan list for correct
scanner configuration.
Green
flashing
Warning
On-line but not allocated to master.
IntelliVAC Plus is on-line but not
allocated to a master.
Check DeviceNet master and its scan list for correct
scanner configuration.
Green
solid
None
Normal operation and allocated to master
1. No action required
Red
flashing
Warning
I/O connection timed-out
Reset DeviceNet master device.
Red
solid
Fault
Bus Off or Duplicate address or Invalid
baud
Diagnostics test failed on power-up reset.
Internal fault exists.
Duplicate DeviceNet node address exists
(two DeviceNet nodes cannot hav e the
same address).
Invalid baud rate (if autobaud is disabled).
Cycle power to the unit and network. If the fault still
exists, replace the IntelliVAC Plus unit.
Change the value of Parameter 57, NonVol MAC ID,
to a valid address and reset the device.
This will only occur if Parameter 55,
AutoBaudEnable, is set to ‘disabled’. Set Parameter
55 to ‘enabled’ and reset the IntelliVAC Plus unit or
set Parameter 56, NonVol Baud Rate, to the correct
setting and reset the IntelliVAC Plus unit.
- IntelliVAC™ Plus Contactor 1
- Control Module 1
- Important User Information 2
- Table of Contents 3
- Chapter 6 6
- Chapter 7 Communications 6
- Chapter 8 Configurations 6
- Chapter 9 DeviceLogix 7
- Product Description 11
- Description 12
- TOP VIEW 14
- IntelliVAC Features 15
- IntelliVAC Base Module 15
- Versions 15
- I M P O R T A N T 16
- Specifications (cont.) 19
- Receiving and Storage 22
- 2-2 Receiving and Storage 23
- Installation 24
- 3-2 Installation 25
- Installation 3-3 26
- Description of Features 28
- Contactor Close 31
- Re-Closing Control 32
- Features 32
- Delayed Restart (General) 33
- Temporary Jog Function 34
- Table 4.D – Event Log Data 36
- Time Stamp 36
- 37
- Valid Data Range 41
- Altitude/Air Pressure 43
- Compensation (400A 43
- Contactors) 43
- RS NetWorx Software 48
- Dual Power Supply Operation 48
- Power Fail Operation 48
- Status Display Items 49
- Contactor Fails to Pick Up 54
- IE Module/Network 59
- Status LEDs 59
- DeviceNet Power Loss 64
- Network Status 67
- (DeviceNet) 67
- (cont.) 68
- Output LEDs 75
- Input LEDs 75
- IntelliVAC Plus Basic Wiring 76
- Ground Connection 77
- CONTACTOR INTERFACE 78
- 11 128 9 105 6 72 3 41 78
- EX. CAP 78
- Wiring Guidelines 79
- Electrically Held 79
- Contactors 79
- Three-Wire Control 80
- Contactors (cont.) 81
- Mechanical Latch 82
- Capacitor Trip 83
- Wiring 88
- 6-2 Wiring (MC) 89
- Wiring (MC) 6-3 90
- 6-4 Wiring (MC) 91
- Wiring (MC) 6-5 92
- 6-6 Wiring (MC) 93
- Wiring (MC) 6-7 94
- 6-8 Wiring (MC) 95
- Incomplete Sequence Timer 96
- Transition Timer 96
- 6-10 Wiring (MC) 97
- 6-12 Wiring (MC) 99
- Communications 100
- DeviceNet 101
- DeviceNet MACID 102
- 7-4 Communications 103
- Communications 7-5 104
- 7-6 Communications 105
- Configuration/Programming 106
- Contactor Drop 107
- Out Time 107
- Table 8.C – Contactor Type 108
- Table 8.G – Future Use 110
- TERMINATION 111
- Programming 112
- Power down the unit 113
- Select “send file” 117
- Select “send” 117
- IE/IB Firmware Revisions 122
- DeviceLogix 124
- 9-2 DeviceLogix 125
- What is DeviceLogix 126
- Inputs and Outputs 126
- Input and Output Bits 126
- Local Function Block Logic 127
- DeviceLogix Operating Modes 128
- 9-6 DeviceLogix 129
- DeviceLogix 9-7 130
- 9-8 DeviceLogix 131
- DeviceLogix 9-9 132
- 9-10 DeviceLogix 133
- 9-12 DeviceLogix 135
- DeviceLogix 9-13 136
- Pulse Timer 138
- On Delay Timer 139
- Go Online 144
- Entering Logic Into 146
- The Editor 146
- Assume Data Available 147
- Figure 9.15 – Forcing 149
- Table 9.I – Input Forcing 149
- Table 9.J – Output Forcing 150
- 9-28 DeviceLogix 151
- Network Boolean Inputs 157
- Output bits/tags 158
- Hardware Boolean Outputs 158
- Network Boolean Outputs 158
- Simple example 160
- DeviceLogix 9-39 162
- 9-40 DeviceLogix 163
- Troubleshooting 164
- Status LED 167
- 2 pulses 169
- 5 pulses 169
- 6 pulses 169
- 7 pulses 170
- 8 pulses 170
- Segment LED Display 172
- Appendix A 174
- Fuse Protection 174
- A-2 Fuse Protection 175
- Parameters 176
- B-4 Parameters 179
- Parameters B-5 180
- B-6 Parameters 181
- Parameters B-7 182
- B-8 Parameters 183
- Parameters B-9 184
- B-10 Parameters 185
- Parameters B-11 186
- B-12 Parameters 187
- Parameters B-13 188
- B-14 Parameters 189
- Parameters B-15 190
- B-16 Parameters 191
- Parameters B-17 192
- B-18 Parameters 193
- Parameters B-19 194
- B-20 Parameters 195
- Parameters B-21 196
- B-22 Parameters 197
- Parameters B-23 198
- B-24 Parameters 199
- Parameters B-25 200
- B-26 Parameters 201
- Parameters B-27 202
- B-28 Parameters 203
- Parameters B-29 204
- B-30 Parameters 205
- Parameters B-31 206
- B-32 Parameters 207
- Table B.7 – Control Masks 211
- Parameters B-37 212
- B-42 Parameters 217
- Parameters B-55 230
- B-56 Parameters 231
- Parameters B-57 232
- B-58 Parameters 233
- Parameters B-59 234
- B-60 Parameters 235
- Parameters B-61 236
- B-62 Parameters 237
- Parameters B-63 238
- B-64 Parameters 239
- Parameters B-69 244
- B-74 Parameters 249
- Parameters B-75 250
- B-76 Parameters 251
- Parameters B-77 252
- B-78 Parameters 253
- Parameters B-79 254
- B-80 Parameters 255
- Parameters B-81 256
- B-82 Parameters 257
- Parameters B-83 258
- B-84 Parameters 259
- Parameters B-85 260
- B-86 Parameters 261
- Parameters B-87 262
- B-88 Parameters 263
- Parameters B-89 264
- B-90 Parameters 265
- Parameters B-91 266
- B-92 Parameters 267
- Parameters B-93 268
- B-94 Parameters 269
- Parameters B-95 270
- B-96 Parameters 271
- Parameters B-97 272
- B-98 Parameters 273
- Parameters B-99 274
- B-100 Parameters 275
- Parameters B-101 276
- B-102 Parameters 277
- Parameters B-103 278
- B-104 Parameters 279
- Parameters B-105 280
- B-106 Parameters 281
- Parameters B-107 282
- B-108 Parameters 283
- Parameters B-109 284
- B-110 Parameters 285
- Parameters B-111 286
- B-112 Parameters 287
- B-114 Parameters 289
- Parameters B-115 290
- B-116 Parameters 291
- Parameters B-117 292
- B-118 Parameters 293
- Parameters B-119 294
- B-120 Parameters 295
- Parameters B-121 296
- B-122 Parameters 297
- B-128 Parameters 303
- Parameters B-129 304
- Parameters B-135 310
- B-136 Parameters 311
- Parameters B-137 312
- B-138 Parameters 313
- Parameters B-139 314
- B-140 Parameters 315
- Parameters B-141 316
- B-142 Parameters 317
- Parameters B-143 318
- B-144 Parameters 319
- Parameters B-145 320
- B-146 Parameters 321
- Parameters B-147 322
- B-148 Parameters 323
- Parameters B-149 324
- B-150 Parameters 325
- Parameters B-151 326
- B-152 Parameters 327
- Parameters B-153 328
- B-154 Parameters 329
- Parameters B-155 330
- B-156 Parameters 331
- Parameters B-157 332
- B-158 Parameters 333
- Parameters B-159 334
- B-160 Parameters 335
- Parameters B-161 336
- B-162 Parameters 337
- Parameters B-163 338
- B-164 Parameters 339
- Parameters B-165 340
- B-166 Parameters 341
- B-168 Parameters 343
- Parameters B-169 344
- B-170 Parameters 345
- Parameters B-171 346
- B-172 Parameters 347
- B-178 Parameters 353
- Parameters B-179 354
- B-182 Parameters 357
- B-184 Parameters 359
- Parameters B-185 360
- B-186 Parameters 361
- Appendix C 362
- Maintenance 362
- Battery Holder 363
- Appendix D 364
- Spare Parts 364
- D-2 Spare Parts 365
- Appendix E 366
- DeviceNet Information 366
- DeviceNet Object 367
- Explicit Connection 369
- Parameter Object 370
- Common Service 371
- IB OutA=close coil command 372
- IB OutB=open coil command 372
- 1503-UM054C-EN-P – June 2013 373
- Important Notes: 374
- DNI (IE) Object 374
- Table E.26 - Common Services 379
- Class Attributes: None 380
- Number of Instances: 1 380
- Data Table Layout 381
- E-18 DeviceNet Information 383
- Appendix F 384
- IntelliVAC Plus Firmware 384
- Medium Voltage Products 387
Relacionado con productos y manuales para Equipo Rockwell-automation 1503VC IntelliVAC Plus Contactor Control Module
Equipo Rockwell-automation 14885P KwikLink Lite, Field Network Pressure-Welde Manual de usuario
(3 paginas)
(3 paginas)
Equipo Rockwell-automation 1492-CM1771-LA002 Analog I/O Conversion Module Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1494V-DS200_DSX200 Disconnect (200A) Quick Install Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1492-CM800-LD015 Field Wire Conv. Module for Modic Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation 1492 Accessory Modules For Circuit Breakers Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1336E IMPACT Adjustable Frequency AC Drive User Ma Manual de usuario
(419 paginas)
(419 paginas)
Equipo Rockwell-automation 1606-XLS240-UPS_UPSD_UPSE DC-UPS Uninterruptible P Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1492-PLTKIT Series E plotter using the USB Port Fi Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales