Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3 Manual de usuario Pagina 156
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
APPENDIX B
FlexPak 3000 49’1340 e
B-52
OIM Menu Path(s): Drive Reference - Drive Reference Trim
The choices are:
• REGISTER: The reference is TRIM REF REGISTER (P.107)
• ANALOG MANUAL: The reference is the analog manual reference input from terminals 16, 17,
and 18 of the Regulator board. Do not select this option if this input is being used for the analog
manual speed reference.
• ANALOG IN 1 or 2: The reference is from an I/O Expansion kit analog input. These are only
available if an I/O Expansion kit is installed.
• NETW IN REG 1, 2, or 3: The reference is from a network input register. These options are
available only if a network kit is installed. Note that the network input registers are updated only
when CONTROL SOURCE SELECT (P.000) is set to network and the network is active.
TRIM REF REGISTER (P.107)
Drive register to manually set the trim reference value used by the drive.
Parameter Range: +100.0%
Default Setting: 0%
Parameter Type: Tuneable
OIM Menu Path(s): Drive Reference - Drive Reference Trim
UNDERWIND ENABLE (Alternate network map, Drop_1, register 32, Bit 5)
Setting this bit to 1 enables two inverter blocks that permit underwind operation.
Setting this bit to 0 disables the two inverter blocks and permits overwind operation.
Parameter Range: 0 = DISABLED (overwind) 1 = ENABLED (underwind)
Default Setting: 0
Parameter Type: Configurable
OIM Menu Path(s): This parameter is available over the network, alternate network map,
drop_1, register 32, bit 5. It cannot be viewed through the
OIM or DCM.
To use this register,
CONTROL SOURCE SELECT must be set to NETWORK and NETW REGISTER MAP SEL
(P.914) must be set to
ALTERNATE.
The inverters are added to the speed loop block and the current minor loop reference block.
ATTENTION: If CONTROL SOURCE is changed from NETWORK to any other control source, the
UNDERWIND ENABLE bit is forced to the default if DISABLED. If the setting was ENABLED and CONTROL
SOURCE is changed from NETWORK, the motor rotates in the opposite direction when the drive is
restarted. The active speed reference should be set to zero before starting the drive from the new
control source. Slowly increase the speed reference until the proper rotation direction can be
determined. If it is incorrect, change the setting of the FORWARD/REVERSE input. The active speed
reference is based on the new control source and the AUTO/MANUAL setting.
From Speed Reference
Mode Select Block Diagram
(SPD LOOP REFERENCE)
(SPD LOOP ERROR)
+
D
.
5
(
E
)
P
.
2
9
5
P
.
2
9
7
MUL
IN
A * B
1000
UNDERWIND ENABLE 1)
Netw. Drop 1, Reg. 32, Bit 5
SPEED FEEDBACK GAIN 1)
Netw. Drop 1, Reg. 38
KEYPAD,
TERMBLK
or SERIAL
EN
To CML Reference
Block Diagram
(SPD LOOP OUTPUT)
PI
KP
HI
WLD
LO
P
.
2
9
9
INIT
RST
SPD LOOP LAG FREQ
SPD LOOP
LAG BYPASS
WLG
LAG
(SPD LOOP
LAG OUTPUT)
P
.
2
1
5
P
.
2
1
7
P
.
2
9
8
OFF
*ON
OUT
NETWORK
P.000 CSS
- FlexPak 3000 Power Module 1
- SW-Version 4.3 1
- Instruction Manual 1
- Table of Contents 3
- 6.0 Quick Start 6-1..6-10 4
- Appendices 5
- List of Figures 6
- List of Tables 6
- 1.1 Safety Instructions 7
- 1.2 General Notes 8
- 1.3 Manual Scope 8
- 1.4 Related User Manuals 8
- 2.1 Drive Identification 9
- 2.2 Drive Specifications 10
- 2.2.6 DC Voltage Ratings: 11
- (-73/43) I 12
- 2.3.1 Logic Inputs: 13
- 2.3.2 Logic Outputs: 13
- 2.3.3 Analog Inputs: 13
- 2.3.4 Analog Outputs: 14
- 2.4 Drive Description 15
- (M/N 317C160D) 16
- (M/N 905FK0101) 16
- 2.5 Controls/Indicators 17
- 2.5.2 Controls 18
- FAULT KEYPAD MANUAL FORWARD 20
- ALARM KEYPAD MANUAL FORWARD 20
- DIAGS KEYPAD MANUAL FORWARD 20
- 3.1 General 25
- 3.3 Install the Drive 25
- 1C 1U 1V 1W 1D 27
- 25 Ø 1) 29
- 3.6 Install the Motor 33
- 3.8 Wire the Drive 34
- 3.8.6 Stopping the Drive 35
- INSTALLATION AND WIRING 38
- 1LG 1 2 03 42
- 4.1 Introduction 43
- 4.2 Test Equipment Needed 43
- 4.3 Power Off Inspection 43
- 4.4 Motor Ground Check 43
- 4.5 Jumper Settings 44
- 4.6 Powering Up the Drive 49
- 4.8 Accessing the Main Menu 50
- Self Tuning 51
- CML Feedback Scaling* 51
- Adjustments 52
- 4.13 Language Selection 53
- 4.14 Programming Features 54
- 4.14.3 Memory Operations 55
- 4.14.4 Reset Clock 56
- 4.14.5 Define User Units 56
- 4.14.5.2 Define Load Units 58
- 5.1 Introduction 59
- " UP 60
- LEFT 60
- & RIGHT 60
- 6.0 Quick Start 63
- 6.1 Introduction 63
- N/A = Not Applicable 69
- 6.4.1 Self Tune Setup 70
- 6.4.2 Execute Self-tuning 71
- 6.5 Final Adjustments 72
- 7.1 General 73
- 7.2 Wiring Errors 73
- 7.3 AC Line and Power Input 73
- 7.4 DC Motor 73
- 7.5 Remote M Contactor 74
- 7.6 Optional Kits 74
- 7.7.2 About The Alarm Menu 75
- 7.7.3 Diagnostics Menu 77
- 7.7.4 Diagnostics Configure 77
- CPU OK LED OIM COMM OK LED 78
- Replacement of a thyristor 82
- 8.2 Accessories 86
- Fuse Holder Dimensions 87
- 80 (110) 88
- L2 L3 PE 89
- (1) (2) 90
- EMC Filters for FlexPak 3000 91
- HF Filter 91
- RFI Filter Selection 92
- E L3 L2 L1 93
- E L3 L2 L1 94
- E L1 L2 L3 95
- LOAD 97
- Terminal 97
- E L3 L2 L1 98
- ∅10.5 ∅10.5 100
- ∅11 ∅12 100
- ∅14 ∅12 100
- FlexPak 3000 49’1340 e 102
- Glossary of Terms 103
- • Application 104
- Typically, it will be 0 106
- ± TOP SPEED 109
- ± MOTOR RATED ARM VOLTS 109
- Frequency Input 113
- (A) terminal 39 113
- (A) terminal 40 113
- (COM) terminal 41 113
- SPEED LOOP 114
- CURRENT LOOP 114
- Installed 116
- Not Installed 116
- • AC TACH is selected 118
- WLD RST\ RATIO 141
- * DISABLED 142
- TOP SPEED 142
- SPEED RAMP 142
- OUTPUT (RPM) 142
- (P.011) 143
- ≠ Network 152
- °, return to step 2 154
- • No Trim 155
- • Incremental 155
- 0 (P.490) 159
- APPENDIX D 169
- FlexPak 3000 D-I 169
- KEYPAD] 169
- D-II FlexPak 3000 49’1340 e 170
- 49’1340 e FlexPak 3000 D-1 171
- 49’1340 e FlexPak 3000 D-3 173
- 49’1340 e FlexPak 3000 D-5 175
- Figure D.6 - Speed Loop 176
- Digital Outputs 1 and 2 177
- Analog and Frequency Outputs 177
- Meter Outputs (n = 1, 2) 178
- 49’1340 e FlexPak 3000 D-9 179
- Figure D.11 - Field Block 181
- Analog Inputs 183
- Level Detectors 1 and 2 184
- APPENDIX E 185
- FlexPak 3000 E-1 185
- FlexPak 3000 49’1340 e 186
- CODE DISPLAY DESCRIPTION 186
- FlexPak 3000 E-3 187
- (P.228) 188
- FlexPak 3000 E-5 189
- FlexPak 3000 E-7 191
- OIM Parameter Menu Tree 193
- APPENDIX F 194
- FlexPak 3000 49'1340 e 194
- FlexPak 3000 F-3 195
- FlexPak 3000 F-5 197
- FlexPak 3000 F-7 199
- 49’1340 e FlexPak 3000 G-1 201
- (continued) 202
- 49’1340 e FlexPak 3000 G-3 203
- 49’1340 e FlexPak 3000 G-5 205
- (on I/O card) 205
- 49’1340 e FlexPak 3000 G-7 207
- EMC Directive 209
- Mounting Instructions 210
- Screen 211
- Screened 3-wire 211
- Shielded 2-wire 211
- Wiring Instruction 212
- APPENDIX J 213
- FlexPak 3000 J-1 213
Relacionado con productos y manuales para Equipo Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3
Equipo Rockwell-automation CS3000 V6.1 MMI FlexPak, GV 3000, Liqui-Flo Manual de usuario
(100 paginas)
(100 paginas)
Equipo Rockwell-automation 440N Ferrocode Coded Magnetic Safety Switch Contro Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation MD60 Serial Converter Module - M/N MDCOMM 232 Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation 20D PowerFlex 700H/S Frame 14 Replacement Power St Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation T8873 Trusted 16 Channel 120V ac Isolated Digital Manual de usuario
(18 paginas)
(18 paginas)
Equipo Rockwell-automation T80015 Application Note Trusted SC300E Migration P Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1769-L24ER-QB1B_L24ER-QBFC1B_L27ERM-QBFC1B Compact Manual de usuario
(86 paginas)
(86 paginas)
Equipo Rockwell-automation MMCL Using the Mining, Mineral, and Cement Library Manual de usuario
(92 paginas)
(92 paginas)
Equipo Rockwell-automation 1900 General Handling Procedures for Medium Voltag Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 20D PowerFlex 700S and 700H Frame 12 DC Bus Connec Manual de usuario
(34 paginas)
(34 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales