Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3 Manual de usuario Pagina 66
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
QUICK START
FlexPak 3000 49’1340 e
6-4
Table 6.2 - Quick Start Parameter Modification Sequence. - continued
Step
No.
Parameter
Name
Code
No.
Default Description User
Setting
3 MOTOR
RATED ARM
VOLTS
009 400 VOLTS
The rated armature voltage from the motor
nameplate.
4 REVERSE
DISABLE
015 OFF* NOTE: This parameter might be affected by
FEEDBACK SELECT, step 5.
When
ON, REVERSE DISABLE prevents the
speed reference from dropping below zero.
The reverse bridge cannot be activated.
When OFF, the speed reference can drop
below zero and the drive can reverse.
*The default is ON when:
• The drive has a non-regen. (S6) power unit.
•
FEEDBACK SELECT is set to AC TACH.
•
FEEDBACK SELECT is set to PULSE TACH
and
PULSE TACH QUADRATURE is OFF.
5 FEEDBACK
SELECT
200
ARMATURE
VOLT
Determines the type of feedback signal that is
used for the speed/voltage loop:
PULSE TACH can be selected only if a pulse
tachometer kit is installed.
FEEDBACK SELECT causes the NEGATIVE
CURRENT LIM (step 16) to be set to 0 and
REVERSE DISABLE to be set to ON if:
•
AC TACH is selected.
•
PULSE TACH is selected and PULSE TACH
QUAD is set OFF.
6 ANLG TACH
VOLTS/1000
203 60 V/1000
RPM
Only needs to be set if FEEDBACK SELECT is
set to
AC TACH or DC TACH.
This parameter is the analog tachometer
scaling from the tachometer nameplate in volts
per 1000 RPM.
It might be limited to less than 200.0
volts/1000 so that voltage from the tachometer
will not be more than 250 V.
7 PULSE TACH
PPR
207 1024 PPR
Only displayed if
FEEDBACK SELECT Is set to
PULSE TACH and a pulse tach interface is
installed.
It sets the pulse encoder pulses per revolution
(PPR) from the pulse encoder nameplate.
8 PULSE TACH
QUADRA-
TURE
208 ON
Only displayed if
FEEDBACK SELECT is set to
PULSE TACH and a pulse tach interface is
installed. Enables or disables pulse encoder
quadrature.
Set ON for a bi-directional pulse encoder.
Set OFF for a unidirectional pulse encoder.
If
PULSE TACH QUADRATURE is set to OFF
while
PULSE TACH is the selected FEEDBACK
SELECT type, NEGATIVE CURRENT LIM will
be set to 0 and
REVERSE DISABLE set to ON
(preventing reverse direction).
- FlexPak 3000 Power Module 1
- SW-Version 4.3 1
- Instruction Manual 1
- Table of Contents 3
- 6.0 Quick Start 6-1..6-10 4
- Appendices 5
- List of Figures 6
- List of Tables 6
- 1.1 Safety Instructions 7
- 1.2 General Notes 8
- 1.3 Manual Scope 8
- 1.4 Related User Manuals 8
- 2.1 Drive Identification 9
- 2.2 Drive Specifications 10
- 2.2.6 DC Voltage Ratings: 11
- (-73/43) I 12
- 2.3.1 Logic Inputs: 13
- 2.3.2 Logic Outputs: 13
- 2.3.3 Analog Inputs: 13
- 2.3.4 Analog Outputs: 14
- 2.4 Drive Description 15
- (M/N 317C160D) 16
- (M/N 905FK0101) 16
- 2.5 Controls/Indicators 17
- 2.5.2 Controls 18
- FAULT KEYPAD MANUAL FORWARD 20
- ALARM KEYPAD MANUAL FORWARD 20
- DIAGS KEYPAD MANUAL FORWARD 20
- 3.1 General 25
- 3.3 Install the Drive 25
- 1C 1U 1V 1W 1D 27
- 25 Ø 1) 29
- 3.6 Install the Motor 33
- 3.8 Wire the Drive 34
- 3.8.6 Stopping the Drive 35
- INSTALLATION AND WIRING 38
- 1LG 1 2 03 42
- 4.1 Introduction 43
- 4.2 Test Equipment Needed 43
- 4.3 Power Off Inspection 43
- 4.4 Motor Ground Check 43
- 4.5 Jumper Settings 44
- 4.6 Powering Up the Drive 49
- 4.8 Accessing the Main Menu 50
- Self Tuning 51
- CML Feedback Scaling* 51
- Adjustments 52
- 4.13 Language Selection 53
- 4.14 Programming Features 54
- 4.14.3 Memory Operations 55
- 4.14.4 Reset Clock 56
- 4.14.5 Define User Units 56
- 4.14.5.2 Define Load Units 58
- 5.1 Introduction 59
- " UP 60
- LEFT 60
- & RIGHT 60
- 6.0 Quick Start 63
- 6.1 Introduction 63
- N/A = Not Applicable 69
- 6.4.1 Self Tune Setup 70
- 6.4.2 Execute Self-tuning 71
- 6.5 Final Adjustments 72
- 7.1 General 73
- 7.2 Wiring Errors 73
- 7.3 AC Line and Power Input 73
- 7.4 DC Motor 73
- 7.5 Remote M Contactor 74
- 7.6 Optional Kits 74
- 7.7.2 About The Alarm Menu 75
- 7.7.3 Diagnostics Menu 77
- 7.7.4 Diagnostics Configure 77
- CPU OK LED OIM COMM OK LED 78
- Replacement of a thyristor 82
- 8.2 Accessories 86
- Fuse Holder Dimensions 87
- 80 (110) 88
- L2 L3 PE 89
- (1) (2) 90
- EMC Filters for FlexPak 3000 91
- HF Filter 91
- RFI Filter Selection 92
- E L3 L2 L1 93
- E L3 L2 L1 94
- E L1 L2 L3 95
- LOAD 97
- Terminal 97
- E L3 L2 L1 98
- ∅10.5 ∅10.5 100
- ∅11 ∅12 100
- ∅14 ∅12 100
- FlexPak 3000 49’1340 e 102
- Glossary of Terms 103
- • Application 104
- Typically, it will be 0 106
- ± TOP SPEED 109
- ± MOTOR RATED ARM VOLTS 109
- Frequency Input 113
- (A) terminal 39 113
- (A) terminal 40 113
- (COM) terminal 41 113
- SPEED LOOP 114
- CURRENT LOOP 114
- Installed 116
- Not Installed 116
- • AC TACH is selected 118
- WLD RST\ RATIO 141
- * DISABLED 142
- TOP SPEED 142
- SPEED RAMP 142
- OUTPUT (RPM) 142
- (P.011) 143
- ≠ Network 152
- °, return to step 2 154
- • No Trim 155
- • Incremental 155
- 0 (P.490) 159
- APPENDIX D 169
- FlexPak 3000 D-I 169
- KEYPAD] 169
- D-II FlexPak 3000 49’1340 e 170
- 49’1340 e FlexPak 3000 D-1 171
- 49’1340 e FlexPak 3000 D-3 173
- 49’1340 e FlexPak 3000 D-5 175
- Figure D.6 - Speed Loop 176
- Digital Outputs 1 and 2 177
- Analog and Frequency Outputs 177
- Meter Outputs (n = 1, 2) 178
- 49’1340 e FlexPak 3000 D-9 179
- Figure D.11 - Field Block 181
- Analog Inputs 183
- Level Detectors 1 and 2 184
- APPENDIX E 185
- FlexPak 3000 E-1 185
- FlexPak 3000 49’1340 e 186
- CODE DISPLAY DESCRIPTION 186
- FlexPak 3000 E-3 187
- (P.228) 188
- FlexPak 3000 E-5 189
- FlexPak 3000 E-7 191
- OIM Parameter Menu Tree 193
- APPENDIX F 194
- FlexPak 3000 49'1340 e 194
- FlexPak 3000 F-3 195
- FlexPak 3000 F-5 197
- FlexPak 3000 F-7 199
- 49’1340 e FlexPak 3000 G-1 201
- (continued) 202
- 49’1340 e FlexPak 3000 G-3 203
- 49’1340 e FlexPak 3000 G-5 205
- (on I/O card) 205
- 49’1340 e FlexPak 3000 G-7 207
- EMC Directive 209
- Mounting Instructions 210
- Screen 211
- Screened 3-wire 211
- Shielded 2-wire 211
- Wiring Instruction 212
- APPENDIX J 213
- FlexPak 3000 J-1 213
Relacionado con productos y manuales para Equipo Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3
Equipo Rockwell-automation CS3000 V6.1 MMI FlexPak, GV 3000, Liqui-Flo Manual de usuario
(100 paginas)
(100 paginas)
Equipo Rockwell-automation 440N Ferrocode Coded Magnetic Safety Switch Contro Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation MD60 Serial Converter Module - M/N MDCOMM 232 Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation 20D PowerFlex 700H/S Frame 14 Replacement Power St Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation T8873 Trusted 16 Channel 120V ac Isolated Digital Manual de usuario
(18 paginas)
(18 paginas)
Equipo Rockwell-automation T80015 Application Note Trusted SC300E Migration P Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1769-L24ER-QB1B_L24ER-QBFC1B_L27ERM-QBFC1B Compact Manual de usuario
(86 paginas)
(86 paginas)
Equipo Rockwell-automation MMCL Using the Mining, Mineral, and Cement Library Manual de usuario
(92 paginas)
(92 paginas)
Equipo Rockwell-automation 1900 General Handling Procedures for Medium Voltag Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 20D PowerFlex 700S and 700H Frame 12 DC Bus Connec Manual de usuario
(34 paginas)
(34 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales