Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3 Manual de usuario Pagina 48
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
DRIVE SETUP AND ADJUSTMENT
FlexPak 3000 49’1340 e
4-6
4.5.8 Analog Auto Reference (AUTO REF) - J12 and J10 Jumpers
The AUTOREF Jumpers J12 and J10 select the type of analog auto reference to be used when
the AUTO mode is selected. J12 selects the type of signal - VOLTS (Voltage) or MAMPS (milli-
amps). J10 selects the range.
+ / - 10 VOLTS MAX 4 - 20 mA 10 - 50 mA
J12 J10
J12 J10
J12 J10
!
VOLTS 10 - 50
! !
VOLTS
!
VOLTS 10 - 50
! !
VOLTS
!
VOLTS 10 - 50
! !
VOLTS
!
(BOTH)
! !
4 - 20
!
(BOTH)
! !
4 - 20
!
(BOTH)
! !
4 - 20
!
MAMPS PARK
! !
!
MAMPS PARK
! !
!
MAMPS PARK
! !
Figure 4.2 - AUTO REF Jumpers (J12 and J10)
4.5.9 Armature Current Feedback Scaling (ARM I FB RB) - J18 Jumper
CAUTION:
The drive will not operate at the correct speed if this jumper is not set to the correct position.
Failure to observe this precaution could result in damage to, or destruction of, the equipment.
The ARM I FB RB) Jumper J18 scales the armature current feedback signal. The drive
calculates the value of the burden resistor needed to scale the armature current feedback
signal. The calculations are based on the values of MOTOR RATED ARM AMPS and
MAXIMUM CURRENT.
The OIM displays the correct position of this jumper during the "Quick Start" procedure.
Verify this setting prior to performing the Self Tuning procedure.
4.5.10 Check the FILTER SELECT - J28 Jumper
NOTE: jumper J28 must always be set to position FLDFBK.
4.5.11 Check the POWER INTERFACE – J30 Jumper
This jumper is factory set according to the type of power interface module installed in the drive.
jumper positions are labeled LOW and HIGH. For FlexPak 3000 drives with a nominal voltage
rating AC 575 V, 60 Hz and 690 V, 50 Hz the jumper J30 must be set to HIGH, for all other
drives this jumper must stay in position LOW. Please refer to the ‘AC Input’ data on the
nameplate.
If this jumper is not set to the correct position. nuisance AC line voltage high/low alarms may
occur or, if configured as a voltage regulator, the drive will not operate at the correct speed,
CAUTION:
The drive will not operate at the correct speed if this jumper is not set to the correct position.
Failure to observe this precaution could result in damage to the equipment or in bodily injury.
- FlexPak 3000 Power Module 1
- SW-Version 4.3 1
- Instruction Manual 1
- Table of Contents 3
- 6.0 Quick Start 6-1..6-10 4
- Appendices 5
- List of Figures 6
- List of Tables 6
- 1.1 Safety Instructions 7
- 1.2 General Notes 8
- 1.3 Manual Scope 8
- 1.4 Related User Manuals 8
- 2.1 Drive Identification 9
- 2.2 Drive Specifications 10
- 2.2.6 DC Voltage Ratings: 11
- (-73/43) I 12
- 2.3.1 Logic Inputs: 13
- 2.3.2 Logic Outputs: 13
- 2.3.3 Analog Inputs: 13
- 2.3.4 Analog Outputs: 14
- 2.4 Drive Description 15
- (M/N 317C160D) 16
- (M/N 905FK0101) 16
- 2.5 Controls/Indicators 17
- 2.5.2 Controls 18
- FAULT KEYPAD MANUAL FORWARD 20
- ALARM KEYPAD MANUAL FORWARD 20
- DIAGS KEYPAD MANUAL FORWARD 20
- 3.1 General 25
- 3.3 Install the Drive 25
- 1C 1U 1V 1W 1D 27
- 25 Ø 1) 29
- 3.6 Install the Motor 33
- 3.8 Wire the Drive 34
- 3.8.6 Stopping the Drive 35
- INSTALLATION AND WIRING 38
- 1LG 1 2 03 42
- 4.1 Introduction 43
- 4.2 Test Equipment Needed 43
- 4.3 Power Off Inspection 43
- 4.4 Motor Ground Check 43
- 4.5 Jumper Settings 44
- 4.6 Powering Up the Drive 49
- 4.8 Accessing the Main Menu 50
- Self Tuning 51
- CML Feedback Scaling* 51
- Adjustments 52
- 4.13 Language Selection 53
- 4.14 Programming Features 54
- 4.14.3 Memory Operations 55
- 4.14.4 Reset Clock 56
- 4.14.5 Define User Units 56
- 4.14.5.2 Define Load Units 58
- 5.1 Introduction 59
- " UP 60
- LEFT 60
- & RIGHT 60
- 6.0 Quick Start 63
- 6.1 Introduction 63
- N/A = Not Applicable 69
- 6.4.1 Self Tune Setup 70
- 6.4.2 Execute Self-tuning 71
- 6.5 Final Adjustments 72
- 7.1 General 73
- 7.2 Wiring Errors 73
- 7.3 AC Line and Power Input 73
- 7.4 DC Motor 73
- 7.5 Remote M Contactor 74
- 7.6 Optional Kits 74
- 7.7.2 About The Alarm Menu 75
- 7.7.3 Diagnostics Menu 77
- 7.7.4 Diagnostics Configure 77
- CPU OK LED OIM COMM OK LED 78
- Replacement of a thyristor 82
- 8.2 Accessories 86
- Fuse Holder Dimensions 87
- 80 (110) 88
- L2 L3 PE 89
- (1) (2) 90
- EMC Filters for FlexPak 3000 91
- HF Filter 91
- RFI Filter Selection 92
- E L3 L2 L1 93
- E L3 L2 L1 94
- E L1 L2 L3 95
- LOAD 97
- Terminal 97
- E L3 L2 L1 98
- ∅10.5 ∅10.5 100
- ∅11 ∅12 100
- ∅14 ∅12 100
- FlexPak 3000 49’1340 e 102
- Glossary of Terms 103
- • Application 104
- Typically, it will be 0 106
- ± TOP SPEED 109
- ± MOTOR RATED ARM VOLTS 109
- Frequency Input 113
- (A) terminal 39 113
- (A) terminal 40 113
- (COM) terminal 41 113
- SPEED LOOP 114
- CURRENT LOOP 114
- Installed 116
- Not Installed 116
- • AC TACH is selected 118
- WLD RST\ RATIO 141
- * DISABLED 142
- TOP SPEED 142
- SPEED RAMP 142
- OUTPUT (RPM) 142
- (P.011) 143
- ≠ Network 152
- °, return to step 2 154
- • No Trim 155
- • Incremental 155
- 0 (P.490) 159
- APPENDIX D 169
- FlexPak 3000 D-I 169
- KEYPAD] 169
- D-II FlexPak 3000 49’1340 e 170
- 49’1340 e FlexPak 3000 D-1 171
- 49’1340 e FlexPak 3000 D-3 173
- 49’1340 e FlexPak 3000 D-5 175
- Figure D.6 - Speed Loop 176
- Digital Outputs 1 and 2 177
- Analog and Frequency Outputs 177
- Meter Outputs (n = 1, 2) 178
- 49’1340 e FlexPak 3000 D-9 179
- Figure D.11 - Field Block 181
- Analog Inputs 183
- Level Detectors 1 and 2 184
- APPENDIX E 185
- FlexPak 3000 E-1 185
- FlexPak 3000 49’1340 e 186
- CODE DISPLAY DESCRIPTION 186
- FlexPak 3000 E-3 187
- (P.228) 188
- FlexPak 3000 E-5 189
- FlexPak 3000 E-7 191
- OIM Parameter Menu Tree 193
- APPENDIX F 194
- FlexPak 3000 49'1340 e 194
- FlexPak 3000 F-3 195
- FlexPak 3000 F-5 197
- FlexPak 3000 F-7 199
- 49’1340 e FlexPak 3000 G-1 201
- (continued) 202
- 49’1340 e FlexPak 3000 G-3 203
- 49’1340 e FlexPak 3000 G-5 205
- (on I/O card) 205
- 49’1340 e FlexPak 3000 G-7 207
- EMC Directive 209
- Mounting Instructions 210
- Screen 211
- Screened 3-wire 211
- Shielded 2-wire 211
- Wiring Instruction 212
- APPENDIX J 213
- FlexPak 3000 J-1 213
Relacionado con productos y manuales para Equipo Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3
Equipo Rockwell-automation CS3000 V6.1 MMI FlexPak, GV 3000, Liqui-Flo Manual de usuario
(100 paginas)
(100 paginas)
Equipo Rockwell-automation 440N Ferrocode Coded Magnetic Safety Switch Contro Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation MD60 Serial Converter Module - M/N MDCOMM 232 Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation 20D PowerFlex 700H/S Frame 14 Replacement Power St Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation T8873 Trusted 16 Channel 120V ac Isolated Digital Manual de usuario
(18 paginas)
(18 paginas)
Equipo Rockwell-automation T80015 Application Note Trusted SC300E Migration P Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1769-L24ER-QB1B_L24ER-QBFC1B_L27ERM-QBFC1B Compact Manual de usuario
(86 paginas)
(86 paginas)
Equipo Rockwell-automation MMCL Using the Mining, Mineral, and Cement Library Manual de usuario
(92 paginas)
(92 paginas)
Equipo Rockwell-automation 1900 General Handling Procedures for Medium Voltag Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 20D PowerFlex 700S and 700H Frame 12 DC Bus Connec Manual de usuario
(34 paginas)
(34 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales