Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3 Manual de usuario Pagina 192
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
APPENDIX E
FlexPak 3000 49’1340 e
E-8
Table E.2 - Alarm Codes (Continued)
CODE DISPLAY DESCRIPTION
A00032 SUSTAINED
SPEED
Motor speed did not fall below the STOP SPEED THRESHOLD (P.113) in
the required amount of time during a stop (this time is automatically set
to two times the
DECELERATION RATE (P.002) time).
Possible causes:
• DECELERATION RATE not set properly.
• STOP SPEED THRESHOLD not set properly.
• Overhauling load maintaining motor speed higher than the STOP
SPEED THRESHOLD.
• Incorrect speed/voltage feedback scaling.
A00033 SUSTAINED
ARMATURE
CURRENT
Armature current was unable to reach discontinuous conduction while
stopping the drive.
Possible causes:
• Motor CEMF too high or line voltage too low for proper commutation.
A00050 CML FEEDBACK
SCALING ERROR
Armature current feedback could not be scaled properly based on the
values entered for
MOTOR RATED ARM AMPS and MAXIMUM CURRENT.
Verify that these parameter values are correct for your application.
Verify that
CT TURNS RATIO has been set to the value shown in the
instruction manual based on your drive type.
A00051 LOW MINIMUM
SPEED
The MINIMUM SPEED value is less than 10% of the MAXIMUM
SPEED value. This alarm will not be triggered on power-up. It only
occurs when maximum or minimum speed has changed.
Verify that these parameter values are correct for your application.
A00052
NEG CUR LIM INV
ENABLE CHANGED
The parameter NEG CUR LIM INV EN (P.226) has changed state, either
enabling or disabling the negative current limit inverters. The
parameters
POS CURRENT LIMIT SEL (P.223) and NEG CURRENT LIMIT
SEL
(P.224) have been automatically set to REGISTER- The user should
carefully examine the current limit scheme to avoid unintended
operation by the drive.
A00700 RETENTIVE
MEMORY SAVE
ERROR
An attempt to save information (parameter values, fault log data or the
keypad reverence value) to retentive memory failed. The drive may
continue to be operated.
Possible cause: Regulator board failure.
- FlexPak 3000 Power Module 1
- SW-Version 4.3 1
- Instruction Manual 1
- Table of Contents 3
- 6.0 Quick Start 6-1..6-10 4
- Appendices 5
- List of Figures 6
- List of Tables 6
- 1.1 Safety Instructions 7
- 1.2 General Notes 8
- 1.3 Manual Scope 8
- 1.4 Related User Manuals 8
- 2.1 Drive Identification 9
- 2.2 Drive Specifications 10
- 2.2.6 DC Voltage Ratings: 11
- (-73/43) I 12
- 2.3.1 Logic Inputs: 13
- 2.3.2 Logic Outputs: 13
- 2.3.3 Analog Inputs: 13
- 2.3.4 Analog Outputs: 14
- 2.4 Drive Description 15
- (M/N 317C160D) 16
- (M/N 905FK0101) 16
- 2.5 Controls/Indicators 17
- 2.5.2 Controls 18
- FAULT KEYPAD MANUAL FORWARD 20
- ALARM KEYPAD MANUAL FORWARD 20
- DIAGS KEYPAD MANUAL FORWARD 20
- 3.1 General 25
- 3.3 Install the Drive 25
- 1C 1U 1V 1W 1D 27
- 25 Ø 1) 29
- 3.6 Install the Motor 33
- 3.8 Wire the Drive 34
- 3.8.6 Stopping the Drive 35
- INSTALLATION AND WIRING 38
- 1LG 1 2 03 42
- 4.1 Introduction 43
- 4.2 Test Equipment Needed 43
- 4.3 Power Off Inspection 43
- 4.4 Motor Ground Check 43
- 4.5 Jumper Settings 44
- 4.6 Powering Up the Drive 49
- 4.8 Accessing the Main Menu 50
- Self Tuning 51
- CML Feedback Scaling* 51
- Adjustments 52
- 4.13 Language Selection 53
- 4.14 Programming Features 54
- 4.14.3 Memory Operations 55
- 4.14.4 Reset Clock 56
- 4.14.5 Define User Units 56
- 4.14.5.2 Define Load Units 58
- 5.1 Introduction 59
- " UP 60
- LEFT 60
- & RIGHT 60
- 6.0 Quick Start 63
- 6.1 Introduction 63
- N/A = Not Applicable 69
- 6.4.1 Self Tune Setup 70
- 6.4.2 Execute Self-tuning 71
- 6.5 Final Adjustments 72
- 7.1 General 73
- 7.2 Wiring Errors 73
- 7.3 AC Line and Power Input 73
- 7.4 DC Motor 73
- 7.5 Remote M Contactor 74
- 7.6 Optional Kits 74
- 7.7.2 About The Alarm Menu 75
- 7.7.3 Diagnostics Menu 77
- 7.7.4 Diagnostics Configure 77
- CPU OK LED OIM COMM OK LED 78
- Replacement of a thyristor 82
- 8.2 Accessories 86
- Fuse Holder Dimensions 87
- 80 (110) 88
- L2 L3 PE 89
- (1) (2) 90
- EMC Filters for FlexPak 3000 91
- HF Filter 91
- RFI Filter Selection 92
- E L3 L2 L1 93
- E L3 L2 L1 94
- E L1 L2 L3 95
- LOAD 97
- Terminal 97
- E L3 L2 L1 98
- ∅10.5 ∅10.5 100
- ∅11 ∅12 100
- ∅14 ∅12 100
- FlexPak 3000 49’1340 e 102
- Glossary of Terms 103
- • Application 104
- Typically, it will be 0 106
- ± TOP SPEED 109
- ± MOTOR RATED ARM VOLTS 109
- Frequency Input 113
- (A) terminal 39 113
- (A) terminal 40 113
- (COM) terminal 41 113
- SPEED LOOP 114
- CURRENT LOOP 114
- Installed 116
- Not Installed 116
- • AC TACH is selected 118
- WLD RST\ RATIO 141
- * DISABLED 142
- TOP SPEED 142
- SPEED RAMP 142
- OUTPUT (RPM) 142
- (P.011) 143
- ≠ Network 152
- °, return to step 2 154
- • No Trim 155
- • Incremental 155
- 0 (P.490) 159
- APPENDIX D 169
- FlexPak 3000 D-I 169
- KEYPAD] 169
- D-II FlexPak 3000 49’1340 e 170
- 49’1340 e FlexPak 3000 D-1 171
- 49’1340 e FlexPak 3000 D-3 173
- 49’1340 e FlexPak 3000 D-5 175
- Figure D.6 - Speed Loop 176
- Digital Outputs 1 and 2 177
- Analog and Frequency Outputs 177
- Meter Outputs (n = 1, 2) 178
- 49’1340 e FlexPak 3000 D-9 179
- Figure D.11 - Field Block 181
- Analog Inputs 183
- Level Detectors 1 and 2 184
- APPENDIX E 185
- FlexPak 3000 E-1 185
- FlexPak 3000 49’1340 e 186
- CODE DISPLAY DESCRIPTION 186
- FlexPak 3000 E-3 187
- (P.228) 188
- FlexPak 3000 E-5 189
- FlexPak 3000 E-7 191
- OIM Parameter Menu Tree 193
- APPENDIX F 194
- FlexPak 3000 49'1340 e 194
- FlexPak 3000 F-3 195
- FlexPak 3000 F-5 197
- FlexPak 3000 F-7 199
- 49’1340 e FlexPak 3000 G-1 201
- (continued) 202
- 49’1340 e FlexPak 3000 G-3 203
- 49’1340 e FlexPak 3000 G-5 205
- (on I/O card) 205
- 49’1340 e FlexPak 3000 G-7 207
- EMC Directive 209
- Mounting Instructions 210
- Screen 211
- Screened 3-wire 211
- Shielded 2-wire 211
- Wiring Instruction 212
- APPENDIX J 213
- FlexPak 3000 J-1 213
Relacionado con productos y manuales para Equipo Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3
Equipo Rockwell-automation CS3000 V6.1 MMI FlexPak, GV 3000, Liqui-Flo Manual de usuario
(100 paginas)
(100 paginas)
Equipo Rockwell-automation 440N Ferrocode Coded Magnetic Safety Switch Contro Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation MD60 Serial Converter Module - M/N MDCOMM 232 Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation 20D PowerFlex 700H/S Frame 14 Replacement Power St Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation T8873 Trusted 16 Channel 120V ac Isolated Digital Manual de usuario
(18 paginas)
(18 paginas)
Equipo Rockwell-automation T80015 Application Note Trusted SC300E Migration P Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation 1769-L24ER-QB1B_L24ER-QBFC1B_L27ERM-QBFC1B Compact Manual de usuario
(86 paginas)
(86 paginas)
Equipo Rockwell-automation MMCL Using the Mining, Mineral, and Cement Library Manual de usuario
(92 paginas)
(92 paginas)
Equipo Rockwell-automation 1900 General Handling Procedures for Medium Voltag Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 20D PowerFlex 700S and 700H Frame 12 DC Bus Connec Manual de usuario
(34 paginas)
(34 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales