Rockwell-automation 294E ArmorStart LT EtherNet/IP Version - User Manu Manual de usuario Pagina 158
- Pagina / 252
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
158 Rockwell Automation Publication 290E-UM001B-EN-P - June 2012
Chapter 5 Diagnostics
Fault Diagnostics
Fault diagnostics capabilities built in the ArmorStart LT Distributed Motor
Controller are designed to help you pinpoint a problem for easy troubleshooting
and quick restarting.
Protection Faults
Protection faults will be generated when potentially dangerous or damaging
conditions are detected. Protection faults are also known as “trips” or “faults”.
These faults will be reported in multiple formats, including:
• Bit enumeration in the TripStatus parameter (parameter 16) used as
discrete bits or in DeviceLogix
• In the ArmorStart LT web server for ArmorStart EtherNet/IP version
• As a sequence of LED flashes on the ECM
MS – Module Status
LED
The bicolor (green/red) LED indicates the
status of the module.
Flashing bicolor (red/green) indicates a
self-test on power up.
Flashing green indicates the device has not
been assigned an IP address.
Steady green indicates the device is
configured and operational.
Flashing red indicates a resettable
protection fault exists or the node address
switches have been changed without a
power cycle and do not match the in-use
configuration.
Steady red indicates a non-resettable
protection fault exists.
I/O Status
Enunciators 0…5
LEDs
Six yellow LEDs are numbered 0…5 and
indicate the status of the input/output
connectors. One LED for each I/O point.
Yellow is illuminated when input is valid or
output is on.
Off when input is not valid or the output is
not turned on.
Reset Button The blue reset button will cause a
protection fault reset to occur.
——
Table 25 - ArmorStart LT Status and Diagnostics Indicators
Indicator Description Color_1 Color_2
LED Flash Bit Enumeration Bulletin 290E/291E Trip Status Bits Bulletin 294E Trip Status Bits
10OverloadTrip ➊ OverloadTrip ➊
2 1 PhaseLossTrip PhaseLShortTrip
32UnderPowerTrip ➊ UnderPowerTrip ➊
4 3 SensorShortTrip ➊ SensorShortTrip ➊
5 4 PhaseImbalTrip OverCurrentTrip
65NonVolMemoryTrip ➊ NonVolMemoryTrip ➊
76reserved ParamSyncTrip ➊
87JamTrip DCBusOrOpenDiscnnct ➊
98StallTrip StallTrip ➊
10 9 UnderloadTrip OverTemperature ➊
11 10 reserved GroundFault ➊
12 11 reserved RestartRetries
13 12 reserved DriveHdwFault ➊
- User Manual 1
- Important User Information 2
- General Precautions 3
- Software Requirements 4
- Additional Resources 4
- Installation Assistance 5
- Summary of Changes 7
- New and Updated 7
- Information 7
- European Communities (EC) 9
- Directive Compliance 9
- Low Voltage and EMC 9
- Directives 9
- Introduction 10
- Table of Contents 11
- Chapter 2 12
- Installation and Wiring 12
- Chapter 3 13
- Product Commissioning 13
- Chapter 4 13
- Bulletin 290E/291E/294E 13
- Programmable Parameters 13
- Appendix C 16
- Using DeviceLogix 16
- Product Overview 17
- Features 18
- Feature Description 19
- Network Options 20
- Product Overview Chapter 1 21
- Factory-Installed Options 22
- ArmorStart LT Characteristics 23
- Catalog Number Explanation 24
- Basic Operation 27
- Chapter 1 Product Overview 28
- Motor Circuit 29
- Local I/O 29
- Mode of Operation 30
- Status LEDs and Reset 32
- Electronic Data Sheet (EDS) 33
- Optional HOA Selector 35
- Optional HOA Keypad 35
- Configuration 35
- (Bulletin 290E/291E only) 35
- Bulletin 290E 36
- Bulletin 291E 36
- Keypad with Jog Function 37
- (Bulletin 294E only) 37
- Source Brake Contactor 38
- Cat. No 43
- Wiring Terminal Detail 44
- Branch Circuit Protection 46
- Typical System Example 47
- ArmorConnect Media 48
- ArmorConnect Cable Ratings 49
- Electrical Wiring 50
- Figure 27 - Bulletin 294E VFD 52
- Disconnect 53
- Voltage 53
- Monitoring 53
- USA and Canada Markets 55
- General Wiring 56
- Considerations 56
- Grounding 57
- Power Distribution 58
- AC Line Voltage 58
- Line Reactor 58
- Bulletin 294 Motor Cable 59
- Shielded Cable 60
- Recommended Cord Grips 61
- Shield Terminating Connectors 61
- Electromagnetic 62
- Compatibility (EMC) 62
- Ethernet, DeviceNet, and 63
- I/O Connections 63
- ArmorConnect Power 64
- Media Receptacles 64
- Optional Locking Clip 65
- Static Address Alternative 69
- Using the 70
- Rockwell Automation 70
- BootP/DHCP Utility 70
- Figure 43 - Relation List 71
- Save the Relation List 72
- A DHCP 73
- Embedded Web Server 74
- Network Configuration 75
- Parameter Configuration 76
- How to Add a New Module 78
- Using the Add-On Profile 78
- Electronic Keying 80
- Connections 81
- Configured by 81
- HOA Keypad Option 82
- User Configurable I/O 82
- RSLogix 5000 Add-On Profile 83
- Auto-Generated Tags 85
- Parameter Groups 100
- ArmorStart LT EtherNet/IP 102
- Parameters 102
- Bulletin 290E/291E 102
- Trip Status Group 107
- Basic Configuration Group 111
- Starter Protection Group 112
- User I/O Configuration Group 115
- Advanced Configuration 121
- Bulletin 294E 124
- Motor and Control Group 133
- Speed Control Group 135
- Acceleration 136
- Figure 53 - S Curve 137
- Frequency 148
- DC Injection Braking Mode 149
- Ramp-to-Stop Mode 149
- Min. Derate 151
- No Derate 151
- Max. Derate 151
- IMPORTANT 155
- Diagnostics 157
- Fault Diagnostics 158
- Diagnostics Chapter 5 159
- Quick Reference 160
- Troubleshooting 160
- Fault LED Indications 161
- Bulletin 294E Faults 163
- Specifications 165
- Motor Overload Trip Curves 170
- (Used with ArmorStart LT) 171
- Appendix A 179
- ArmorStart LT 180
- Product Family 180
- Multiple-Motor Branch 181
- Circuits and Motor 181
- Controllers Listed for Group 181
- Installation – General 181
- Maximum Fuse Ampere 183
- Rating According to 183
- 7.2.10.4(1) and 7.2.10.4(2) 183
- Explanatory Example 185
- 14 AWG14 AWG 186
- CIP Information 193
- CIP Explicit Connection 194
- Behavior 194
- CIP Object Requirements 194
- Identity Object 195
- Message Router 196
- Assembly Object 196
- I/O Assemblies 197
- Instance 100 198
- Instance 101 199
- Name Parameter Instance 200
- Instance 150 201
- Instance 152 201
- Instance 154 202
- Instance 156 202
- Connection Manager Object 203
- Class 1 Connections 204
- Class 3 Connections 205
- Discrete Input Point 206
- Discrete Output Point 206
- Appendix B CIP Information 208
- CIP Information Appendix B 209
- Analog Input Point Object 211
- Analog Output Point Object 211
- Parameter Object 212
- Parameter Group Object 213
- Discrete Input 214
- Group Object 214
- Discrete Output 214
- Control Supervisor Object 215
- Overload Object 216
- Device Level Ring (DLR) 217
- Extended Device Object 217
- DPI Fault Object 218
- DPI Alarm Object 222
- TCP/IP Interface Object 223
- Ethernet Link Object 224
- Trip and Warning 226
- Email Object 226
- Using DeviceLogix™ 229
- DeviceLogix Programming 230
- ➊ IPS Units 235
- ArmorStart LT 236
- Download the AOP 237
- ‘Next’ to continue 239
- Use of the AOP 242
- 1756-EN2TR and click OK 244
- Name Value Description 250
- Rockwell Automation Support 252
- Documentation Feedback 252
- Trademark List 252
Relacionado con productos y manuales para Equipo Rockwell-automation 294E ArmorStart LT EtherNet/IP Version - User Manu
Equipo Rockwell-automation 193-EE Bul 193 E1 PLUS Overload Relay Application Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 440P Bulletin 440P 2 N.C. Small Metal Safety Posit Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 150-SM6 SMC-50 Soft Starter Parameter Configuratio Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 440R MSR178DP Minotaur Installation Instructions Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 802PR Type LA and Type XA, Series C Installation I Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 442L SafeZone Singlezone & Multizone Safety La Manual de usuario
(60 paginas)
(60 paginas)
Equipo Rockwell-automation 21G PowerFlex 750-Series AC Drives Programming Man Manual de usuario
(544 paginas)
(544 paginas)
Equipo Rockwell-automation 592-EEKF_EEMG E1 Plus Overload Relay Application a Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 150-SM3_SM4 SMC-50 Soft Starter I/O Option Module Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 284D- ArmorStart Base and Control Module Replaceme Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales