Rockwell-automation 294E ArmorStart LT EtherNet/IP Version - User Manu Manual de usuario Pagina 167
- Pagina / 252
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication 290E-UM001B-EN-P - June 2012 167
Specifications Chapter 6
Input and Output Ratings
Input
Supply Voltage Unswitched power A3/A2
Type of Inputs 24V DC current sinking
Connection Type Single keyed M12, quick disconnect
Input per Connection 1/each
Rated Operating Voltage 24V DC
On-State Input Voltage (pin 4) 10…26.4V DC, nominal 24V DC
Off-State Input Voltage 5V DC
On-State Input Current (pin 4) 1…3.7 mA, 2.6 mA @ 24V DC
Off-State Input Current <1.5 mA
Maximum Sensor Leakage Current <2.5 mA
Maximum Number of Input Devices 6
Maximum Sensor Sourcing Current (pin 1) 50 mA per point (max 300 mA total for sourcing one device)
Sensor Operating Voltage Range 19.2…26V DC
Input Bounce Filter ➊
(Software Configurable)
Off-On or On-Off: 0.5 ms + 64 ms
Filtering 100 μs
DeviceLogix I/O Response 2 ms (500 Hz)
Output
Supply Voltage (Switched Power) A1/A2
Type of Outputs DC sourcing
Load Types Resistive or light inductive
Utilization Category (IEC) DC-1, DC-13
Output State Normally Open (N.O.)
Connection Type Single keyed M12, quick disconnect
Output per Connection 1/each
Overcurrent Protection ➋ 1.5 A (the sum of all outputs cannot exceed this value)
Rated Insulation Voltage (U
i
) UL: 1500V AC, IEC: 2000V AC
Rated Operating Voltage (U
e
) 19.2…26.4V DC
Maximum Blocking Voltage 35V DC
Nominal Operating Current (I
e
) 500 mA per point
Maximum Thermal Current (I
the
) 500 mA per point
Maximum Off-state Leakage Current 1 μA
Maximum Number of Outputs 6
Surge Suppression Integrated diode to protect against switching loads
➊ Input ON-to-OFF delay time is the time from a valid input signal to recognition by the module.
➋ If an output exceeds 1.5 A for greater than 7 ms, a fault is generated.
- User Manual 1
- Important User Information 2
- General Precautions 3
- Software Requirements 4
- Additional Resources 4
- Installation Assistance 5
- Summary of Changes 7
- New and Updated 7
- Information 7
- European Communities (EC) 9
- Directive Compliance 9
- Low Voltage and EMC 9
- Directives 9
- Introduction 10
- Table of Contents 11
- Chapter 2 12
- Installation and Wiring 12
- Chapter 3 13
- Product Commissioning 13
- Chapter 4 13
- Bulletin 290E/291E/294E 13
- Programmable Parameters 13
- Appendix C 16
- Using DeviceLogix 16
- Product Overview 17
- Features 18
- Feature Description 19
- Network Options 20
- Product Overview Chapter 1 21
- Factory-Installed Options 22
- ArmorStart LT Characteristics 23
- Catalog Number Explanation 24
- Basic Operation 27
- Chapter 1 Product Overview 28
- Motor Circuit 29
- Local I/O 29
- Mode of Operation 30
- Status LEDs and Reset 32
- Electronic Data Sheet (EDS) 33
- Optional HOA Selector 35
- Optional HOA Keypad 35
- Configuration 35
- (Bulletin 290E/291E only) 35
- Bulletin 290E 36
- Bulletin 291E 36
- Keypad with Jog Function 37
- (Bulletin 294E only) 37
- Source Brake Contactor 38
- Cat. No 43
- Wiring Terminal Detail 44
- Branch Circuit Protection 46
- Typical System Example 47
- ArmorConnect Media 48
- ArmorConnect Cable Ratings 49
- Electrical Wiring 50
- Figure 27 - Bulletin 294E VFD 52
- Disconnect 53
- Voltage 53
- Monitoring 53
- USA and Canada Markets 55
- General Wiring 56
- Considerations 56
- Grounding 57
- Power Distribution 58
- AC Line Voltage 58
- Line Reactor 58
- Bulletin 294 Motor Cable 59
- Shielded Cable 60
- Recommended Cord Grips 61
- Shield Terminating Connectors 61
- Electromagnetic 62
- Compatibility (EMC) 62
- Ethernet, DeviceNet, and 63
- I/O Connections 63
- ArmorConnect Power 64
- Media Receptacles 64
- Optional Locking Clip 65
- Static Address Alternative 69
- Using the 70
- Rockwell Automation 70
- BootP/DHCP Utility 70
- Figure 43 - Relation List 71
- Save the Relation List 72
- A DHCP 73
- Embedded Web Server 74
- Network Configuration 75
- Parameter Configuration 76
- How to Add a New Module 78
- Using the Add-On Profile 78
- Electronic Keying 80
- Connections 81
- Configured by 81
- HOA Keypad Option 82
- User Configurable I/O 82
- RSLogix 5000 Add-On Profile 83
- Auto-Generated Tags 85
- Parameter Groups 100
- ArmorStart LT EtherNet/IP 102
- Parameters 102
- Bulletin 290E/291E 102
- Trip Status Group 107
- Basic Configuration Group 111
- Starter Protection Group 112
- User I/O Configuration Group 115
- Advanced Configuration 121
- Bulletin 294E 124
- Motor and Control Group 133
- Speed Control Group 135
- Acceleration 136
- Figure 53 - S Curve 137
- Frequency 148
- DC Injection Braking Mode 149
- Ramp-to-Stop Mode 149
- Min. Derate 151
- No Derate 151
- Max. Derate 151
- IMPORTANT 155
- Diagnostics 157
- Fault Diagnostics 158
- Diagnostics Chapter 5 159
- Quick Reference 160
- Troubleshooting 160
- Fault LED Indications 161
- Bulletin 294E Faults 163
- Specifications 165
- Motor Overload Trip Curves 170
- (Used with ArmorStart LT) 171
- Appendix A 179
- ArmorStart LT 180
- Product Family 180
- Multiple-Motor Branch 181
- Circuits and Motor 181
- Controllers Listed for Group 181
- Installation – General 181
- Maximum Fuse Ampere 183
- Rating According to 183
- 7.2.10.4(1) and 7.2.10.4(2) 183
- Explanatory Example 185
- 14 AWG14 AWG 186
- CIP Information 193
- CIP Explicit Connection 194
- Behavior 194
- CIP Object Requirements 194
- Identity Object 195
- Message Router 196
- Assembly Object 196
- I/O Assemblies 197
- Instance 100 198
- Instance 101 199
- Name Parameter Instance 200
- Instance 150 201
- Instance 152 201
- Instance 154 202
- Instance 156 202
- Connection Manager Object 203
- Class 1 Connections 204
- Class 3 Connections 205
- Discrete Input Point 206
- Discrete Output Point 206
- Appendix B CIP Information 208
- CIP Information Appendix B 209
- Analog Input Point Object 211
- Analog Output Point Object 211
- Parameter Object 212
- Parameter Group Object 213
- Discrete Input 214
- Group Object 214
- Discrete Output 214
- Control Supervisor Object 215
- Overload Object 216
- Device Level Ring (DLR) 217
- Extended Device Object 217
- DPI Fault Object 218
- DPI Alarm Object 222
- TCP/IP Interface Object 223
- Ethernet Link Object 224
- Trip and Warning 226
- Email Object 226
- Using DeviceLogix™ 229
- DeviceLogix Programming 230
- ➊ IPS Units 235
- ArmorStart LT 236
- Download the AOP 237
- ‘Next’ to continue 239
- Use of the AOP 242
- 1756-EN2TR and click OK 244
- Name Value Description 250
- Rockwell Automation Support 252
- Documentation Feedback 252
- Trademark List 252
Relacionado con productos y manuales para Equipo Rockwell-automation 294E ArmorStart LT EtherNet/IP Version - User Manu
Equipo Rockwell-automation 193-EE Bul 193 E1 PLUS Overload Relay Application Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 440P Bulletin 440P 2 N.C. Small Metal Safety Posit Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 150-SM6 SMC-50 Soft Starter Parameter Configuratio Manual de usuario
(6 paginas)
(6 paginas)
Equipo Rockwell-automation 440R MSR178DP Minotaur Installation Instructions Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 802PR Type LA and Type XA, Series C Installation I Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 442L SafeZone Singlezone & Multizone Safety La Manual de usuario
(60 paginas)
(60 paginas)
Equipo Rockwell-automation 21G PowerFlex 750-Series AC Drives Programming Man Manual de usuario
(544 paginas)
(544 paginas)
Equipo Rockwell-automation 592-EEKF_EEMG E1 Plus Overload Relay Application a Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 150-SM3_SM4 SMC-50 Soft Starter I/O Option Module Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 284D- ArmorStart Base and Control Module Replaceme Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales