Rockwell-automation IASIMP Computer Numerical Control (CNC) Machining Manual de usuario Pagina 177
- Pagina / 278
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication IASIMP-QS034A-EN-P - October 2012 177
FactoryTalk View ME Configuration Chapter 5
Configure Goto Display Buttons on Startup Display
The Goto buttons on the main startup screen that are used for launching the FANUC CNC faceplates use a
special Goto button that is different than standard device Goto buttons that are included in the startup screen.
The CNC Goto buttons includes a CNC status multi-state indicator directly on the button. For the CNCs in
your application you must replace the default device Goto buttons with the CNC Goto buttons. First you add
the Goto button graphics and objects to your application. Then you place and associate the individual Goto
display buttons to the appropriate faceplate and specific parameter file.
Add FANUC CNC Goto Buttons to Your Application
1. Right-click Display and choose Add Component Into
Application.
2. Browse to C:\Program Files\RA_Simplification\
CMAT\A-Files\5-HMI\ME\HMI Modules\
01_Machine\ME_GoToButtons.
3. Select the Goto_FanucCNC.gfx file and
click Open.
The selected display appears under
Displays in your application.
- Accelerator Toolkit 1
- Important User Information 2
- Chapter 7 3
- Where to Start 4
- Chapter 4 6
- GuardLogix Configuration 6
- Chapter 5 6
- Appendix D 9
- Configuration 9
- Table of Contents 10
- Introduction 11
- Conventions 12
- Required Software 12
- Additional Resources 13
- FANUC CNC Express Software 19
- System Layout and Wiring 29
- • The 07_PLC_1791DS_IB16 and 32
- Project Drawings folder 33
- Edit FANUC CNC Drawing Set 34
- Edit CNC Power Drawings 35
- • 16_CNC_Ethernet_Switch 41
- • 18_CNC_Cable_Connections 41
- CNC Subpanel Layout Drawing 43
- CNC Enclosure Layout Drawing 43
- Drive Power Example 44
- Drive I/O Example 44
- System Layout Example 44
- FANUC CNC Configuration 47
- Parameter Write Enable 49
- High Speed Ethernet Option 51
- Configure Ethernet Module 53
- Create a New Project File 56
- 5. Select the model 58
- USB External Device 63
- EtherNet/IP Settings 64
- Logic Configuration 68
- P0001 (OP Panel Path 1) 71
- P0005 (Machine Sequence) 71
- P0010 (Window Functions) 72
- P0023 (Alarm Routine) 72
- Device Logic Modules 73
- 4. Click to save your FANUC 76
- LADDER III application file 76
- Figure 8 - Logic Modules 81
- Order and Run the DMAT Wizard 84
- Save the Project File 90
- 9. Click OK 94
- FANUC CNC AOP Configuration 95
- Add and Configure FANUC CNC 96
- The Import Configuration 101
- Import 105
- Machining Example 109
- Drill CNC Example 109
- Gantry Y Axis Drive Example 110
- Machine CNC Example 110
- Gantry X Axis Drive Example 110
- • Drill CNC 111
- • Machining CNC 111
- • Gantry X Axis Drive 111
- • Gantry Y Axis Drive 111
- IMPORTANT 113
- _ModuleNameXX tag 116
- Logic Placeholder 121
- Safety Logic Integration 137
- GuardLogix Safety Logic 138
- Safety Faceplate Logic 144
- Before You Begin 149
- What You Need 149
- Follow These Steps 150
- Delete Unused Displays 154
- Delete Unused Parameter Files 155
- Configure Parameter Files 156
- Parameters 157
- Comments 157
- Chapter 6 158
- • SafeIOAlarmTrigger 160
- • ModuleAlarmTrigger 160
- • CNCAlarmTrigger 160
- • CIPMotionAlarmTrigger 160
- Add Parameter Files 165
- Parameters folder 166
- Import Alarm Setup File 171
- • SaveIOAlarmTrigger 173
- Import and Edit Alarm Tags 174
- Goto Display Buttons 189
- CellGuard1 193
- System Commissioning 195
- Download Applications 197
- Terminal 202
- Commissioning Devices 205
- Verify Network Communication 206
- 1756-EN2TR 207
- EtherNet/IP 207
- • If there is an active 211
- Clearing Faults 212
- Operator (manual) Control 212
- Program (automatic) Control 213
- System Application Guide 215
- Machine Startup Faceplate 217
- Machine Control 219
- Program/Operator Mode 219
- CNC Faceplate 221
- CNC Status Views 222
- CNC Control Views 222
- Fault Indication View 223
- Fault Diagnostic Views 224
- Configuration View 225
- Guard I/O Safety Faceplates 226
- Logic Program Overview 229
- Module Routine Overview 231
- Machine Module 234
- Machine Control Module Tags 236
- Application Modules 240
- Device Modules 241
- Logic Module Customization 243
- • Mode = UDT_MachMode 244
- • Command = UDT_MachCmd 244
- • State = UDT_MachState 244
- (2) Refer to Chapter 5 246
- Module Fault Customization 249
- Appendix 255
- Add Optional Faceplate Views 258
- Verify Your IP Address 262
- Load the Controller Firmware 265
- Assign IP Addresses 267
- Numerics 271
- Rockwell Automation Support 278
- Documentation Feedback 278
Relacionado con productos y manuales para Equipo Rockwell-automation IASIMP Computer Numerical Control (CNC) Machining
Equipo Rockwell-automation 440G-TLSGD2 TLSGD2--Compact Tongue Operated Safety Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation SP120 ACDrive 115VAC, 1Ph, 230VAC, 1Ph/3Ph, 1/4-5. Manual de usuario
(210 paginas)
(210 paginas)
Equipo Rockwell-automation MDO16GNS 16-Channel Digital Output Module 48Vdc Manual de usuario
(16 paginas)
(16 paginas)
Equipo Rockwell-automation T80001 Application Note Termination of Class 1 Div Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1440-REX03-04RG XM-442 Voted EODS Relay Module Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation T7454 ICS Regent+Plus AC Isolated Digital Output M Manual de usuario
(13 paginas)
(13 paginas)
Equipo Rockwell-automation TDI16EIA 16-Channel Digital Input Termination Card Manual de usuario
(11 paginas)
(11 paginas)
Equipo Rockwell-automation T80002 Application Note Replacement of Power Suppl Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 2097-V3xPRx-LM Kinetix 300 and Kinetix 350 Drive S Manual de usuario
(84 paginas)
(84 paginas)
Equipo Rockwell-automation WebPak 3000 DC Drives Hardware Reference, Install Manual de usuario
(92 paginas)
(92 paginas)
Equipo Rockwell-automation Drives and Motion Accelerator Toolkit Quick Start Manual de usuario
(8 paginas)
(8 paginas)
Equipo Rockwell-automation T8423 Trusted TMR 35 - 120 Vdc Digital Input Modul Manual de usuario
(33 paginas)
(33 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales