Rockwell-automation 1305 AC Drive, Firmware 1.01-3.00 User Manual Manual de usuario Pagina 76
- Pagina / 162
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 5 –Programming
5-8
Set Up
This group of parameters defines the basic operation of the drive and should be programmed before initial
operation. For advanced programming and information on specific parameters, refer to the flow chart on
page 5-2 & 5-3
[Inp
ut
Mode
]
Parameter # 21 Factory Default “3 wire”
[Inp
ut
Mode
]
Parameter Type Read & Write
This parameter selects between three wire and Run
Fwd/Rev control. Refer to Chapter 2, Figure 2-5.
IMPORTANT: If this parameter is changed while the drive is
operating, power must be cycled to the drive for the change
to take effect. This is required since the start and reverse
functions will operate differently for the two different modes.
Units None Setting “3 Wire”
“Run Fwd/Rev”
IMPORTANT: This parameter cannot be pro-
grammed while the drive is running.
[
F
re
q
Sele
ct 1]
Parameter # 5 Factory Default “Adapter 1”
[
F
re
q
Sele
ct 1]
Parameter Type Read & Write
Settings ‘‘Remote Pot”
‘‘0-10 Volt”
‘‘ –2
‘‘Preset 1”
‘‘Preset 2”
‘‘ rese
This parameter is the factory default parameter for
selecting the frequency source that will supply the [Freq
Command] to the drive. [Freq Select 2] or [Preset Freq
1–7] can be selected in place of this parameter with proper
terminal block inputs. (See Charts on Pages 5-26 and
5-27).
Units None
‘‘
4
–2
0 mA”
‘‘MOP”
‘‘Adapter 1”
‘‘Adapter 2”
‘‘Adapter 3”
‘‘Adapter 4”
‘‘Adapter 5”
‘‘Adapter 6”
‘‘
P
rese
t 3”
‘‘Preset 4”
‘‘Preset 5’’
‘‘Preset 6”
‘‘Preset 7”
[A
cc
el
T
im
e
1]
Parameter # 7 Factory Default 10.0 Sec
[A
cc
el
T
im
e
1]
Parameter Type Read & Write Minimum 0.0 Sec
This parameter is the factory default parameter for
determining the time it will take the drive to ramp from 0 Hz
to [Maximum Frequency]. The rate is linear unless
[S Curve] is ‘‘Enabled.” It applies to any increase in
command frequency. The [Accel Time 2] parameter can
be selected in place of this parameter. (See Charts on
Pages 5-26 and 5-27).
Units 0.1 Second Maximum 3600.0 Sec
- User Manual 1
- Important User Information 2
- Document Update 3
- Summary of Changes 5
- Chapter 4 – Start-Up 8
- Chapter 5 – Programming 8
- Appendix C – Accessories 9
- Table of Contents 10
- Information and Precautions 11
- GENERAL PRECAUTIONS 12
- NAMEPLATE LOCATION 14
- FIRMWARE COMPATIBILITY 14
- Output ➀➁ 16
- Current (A) 16
- Installation/Wiring 17
- TERMINAL BLOCK ACCESS 19
- INPUT DEVICES 21
- INPUT POWER CONDITIONING 22
- INPUT FUSING 22
- RFI FILTERING 24
- GROUNDING 25
- POWER WIRING 27
- DRIVE OPERATION WITHOUT A 31
- HUMAN INTERFACE MODULE (HIM) 31
- CONTROL WIRING 31
- See notes on page 2-18 33
- OUTPUT DEVICES 35
- CABLE TERMINATION 35
- ADAPTERS 36
- Human Interface Module 39
- HIM REMOVAL AND INSTALLATION 42
- HIM MODES 43
- PROGRAM AND DISPLAY MODES 45
- Logic Mask 46
- X1111111 46
- Choose Group 46
- PROCESS MODE 47
- EEPROM MODE 48
- EEPROM MODE (cont.) 49
- SEARCH MODE 51
- CONTROL STATUS MODE 52
- CONTROL STATUS MODE (cont.) 53
- PASSWORD MODE 54
- PASSWORD MODE (cont.) 55
- Start-Up 59
- Chapter 4 –Start–Up 60
- DESCRIPTION 60
- HIM DISPLAY 60
- Reset Factory Defaults 61
- [Input Mode] Selection 61
- Open Enable Signal 64
- Restore Enable Signal 64
- Remove ALL Power 66
- Reconnect Motor 66
- Slowly Increase Speed 68
- Programming 69
- PROGRAMMING EXAMPLE 72
- Metering 73
- Metering Group (cont.) 74
- Set Up Group (cont.) 77
- Advanced Setup 82
- Advanced Set Up Group (cont.) 83
- Frequency 91
- Frequency Set Group (cont.) 92
- “French” 99
- “Italian” 99
- “Japanese” 99
- “Spanish” 99
- “German” 99
- Feature Select Group (cont.) 100
- 0 to [Maximum Freq] 102
- 815V/460V Drives 102
- Chapter 5 –Programming 103
- Cycling Input Power 104
- Diagnostics Group (cont.) 106
- Saves parameter Ram to EEPROM 109
- Masks Group (cont.) 111
- Controlling 114
- Not Controlling 114
- Owners Group (cont.) 115
- Adapter I/O 117
- Adapter I/O Group (cont.) 118
- Process Display 119
- Linear List 120
- CHAPTER OBJECTIVES 121
- FAULT INFORMATION 121
- Table 6.C Troubleshooting 129
- Appendix A – 133
- Appendix B – 139
- Appendix C – 155
Relacionado con productos y manuales para Equipo Rockwell-automation 1305 AC Drive, Firmware 1.01-3.00 User Manual
Equipo Rockwell-automation 1502 400 Amp Medium Voltage Contactor (Series D) Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation 1494C-xxx Cable Operated 30A / 60A / 100A Disconne Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1794-PS13_PS3 FLEX I/O dc Power Supply Install. In Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1787-DNPS DeviceNet Power Supply Installation Inst Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation Logix5000 Program Parameters Programming Manual Manual de usuario
(36 paginas)
(36 paginas)
Equipo Rockwell-automation 1732D-XXXX PointBlock 16 dc Input Module Installat Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1771-CFM Config. Flowmeter Installation Instructio Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O Manual de usuario
(120 paginas)
(120 paginas)
Equipo Rockwell-automation 1769-OA8 Compact 100 to 240V ac Solid State Output Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1734-PDN/B Point I/O DeviceNet Communication Inter Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1786-RPFRXL ControlNet Fiber Ring Modules Installa Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 1732E-XXXX ArmorBlock 2-Port EtherNet/IP Modules w Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales