Rockwell-automation 1305 AC Drive, Firmware 1.01-3.00 User Manual Manual de usuario Pagina 97
- Pagina / 162
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 5 –Programming
5-29
This group contains the necessary parameters to activate and program advanced features of the drive.
Feature
Select
[
Ru
n
On
Po
w
er
U
p
]
Parameter # 14 Factory Default ‘‘Disabled”
[
Ru
n
On
Po
w
er
U
p
]
Parameter Type Read & Write
This parameter enables the function that allows the drive to
automatically restart on power up regardless of what the
drive status was before power is lost. This applies only
when there is a maintained input to the start and stop
inputs. Refer to Chapter 2, Figure 2.5.
Units None Settings ‘‘Enabled”
‘‘Disabled”
ATTENTION: This parameter may only be used as outlined in NFPA 79, paragraph 6-14 (exceptions 1-3) for
specialized applications. Equipment damage and/or personal injury may result if this parameter is used in an
inappropriate application.
[
R
e
s
e
t/Ru
n
Tr
i
e
s]
Parameter # 85 Factory Default 0
[
R
e
s
e
t/Ru
n
Tr
i
e
s]
Parameter Type Read & Write Minimum 0
This value sets the maximum number of times the drive
attempts to reset a fault and restart before the drive issues
a ‘‘Max Retries Fault.” Not operative for faults 9, 10, 11,
24, 25, 26, 29, 30, 32, 33, 34, 35, 38, 39, 40, 41, 42,
43 and 48.
Units None Maximum 9
[
R
e
s
e
t/Ru
n
T
im
e
]
Parameter # 15 Factory Default 1.0 Sec
[
R
e
s
e
t/Ru
n
T
im
e
]
Parameter Type Read & Write Minimum 0.5 Sec
This value sets the time between restart attempts when
[Reset/Run Tries] is a value other than 0.
Units 0.1 Second Maximum 30.0 Sec
- User Manual 1
- Important User Information 2
- Document Update 3
- Summary of Changes 5
- Chapter 4 – Start-Up 8
- Chapter 5 – Programming 8
- Appendix C – Accessories 9
- Table of Contents 10
- Information and Precautions 11
- GENERAL PRECAUTIONS 12
- NAMEPLATE LOCATION 14
- FIRMWARE COMPATIBILITY 14
- Output ➀➁ 16
- Current (A) 16
- Installation/Wiring 17
- TERMINAL BLOCK ACCESS 19
- INPUT DEVICES 21
- INPUT POWER CONDITIONING 22
- INPUT FUSING 22
- RFI FILTERING 24
- GROUNDING 25
- POWER WIRING 27
- DRIVE OPERATION WITHOUT A 31
- HUMAN INTERFACE MODULE (HIM) 31
- CONTROL WIRING 31
- See notes on page 2-18 33
- OUTPUT DEVICES 35
- CABLE TERMINATION 35
- ADAPTERS 36
- Human Interface Module 39
- HIM REMOVAL AND INSTALLATION 42
- HIM MODES 43
- PROGRAM AND DISPLAY MODES 45
- Logic Mask 46
- X1111111 46
- Choose Group 46
- PROCESS MODE 47
- EEPROM MODE 48
- EEPROM MODE (cont.) 49
- SEARCH MODE 51
- CONTROL STATUS MODE 52
- CONTROL STATUS MODE (cont.) 53
- PASSWORD MODE 54
- PASSWORD MODE (cont.) 55
- Start-Up 59
- Chapter 4 –Start–Up 60
- DESCRIPTION 60
- HIM DISPLAY 60
- Reset Factory Defaults 61
- [Input Mode] Selection 61
- Open Enable Signal 64
- Restore Enable Signal 64
- Remove ALL Power 66
- Reconnect Motor 66
- Slowly Increase Speed 68
- Programming 69
- PROGRAMMING EXAMPLE 72
- Metering 73
- Metering Group (cont.) 74
- Set Up Group (cont.) 77
- Advanced Setup 82
- Advanced Set Up Group (cont.) 83
- Frequency 91
- Frequency Set Group (cont.) 92
- “French” 99
- “Italian” 99
- “Japanese” 99
- “Spanish” 99
- “German” 99
- Feature Select Group (cont.) 100
- 0 to [Maximum Freq] 102
- 815V/460V Drives 102
- Chapter 5 –Programming 103
- Cycling Input Power 104
- Diagnostics Group (cont.) 106
- Saves parameter Ram to EEPROM 109
- Masks Group (cont.) 111
- Controlling 114
- Not Controlling 114
- Owners Group (cont.) 115
- Adapter I/O 117
- Adapter I/O Group (cont.) 118
- Process Display 119
- Linear List 120
- CHAPTER OBJECTIVES 121
- FAULT INFORMATION 121
- Table 6.C Troubleshooting 129
- Appendix A – 133
- Appendix B – 139
- Appendix C – 155
Relacionado con productos y manuales para Equipo Rockwell-automation 1305 AC Drive, Firmware 1.01-3.00 User Manual
Equipo Rockwell-automation 1502 400 Amp Medium Voltage Contactor (Series D) Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation 1494C-xxx Cable Operated 30A / 60A / 100A Disconne Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1794-PS13_PS3 FLEX I/O dc Power Supply Install. In Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1787-DNPS DeviceNet Power Supply Installation Inst Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation Logix5000 Program Parameters Programming Manual Manual de usuario
(36 paginas)
(36 paginas)
Equipo Rockwell-automation 1732D-XXXX PointBlock 16 dc Input Module Installat Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1771-CFM Config. Flowmeter Installation Instructio Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O Manual de usuario
(120 paginas)
(120 paginas)
Equipo Rockwell-automation 1769-OA8 Compact 100 to 240V ac Solid State Output Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1734-PDN/B Point I/O DeviceNet Communication Inter Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1786-RPFRXL ControlNet Fiber Ring Modules Installa Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 1732E-XXXX ArmorBlock 2-Port EtherNet/IP Modules w Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.124 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales