Rockwell-automation 1305 AC Drive, Firmware 1.01-3.00 User Manual Manual de usuario Pagina 79
- Pagina / 162
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 5 –Programming
5-11
Set Up Group (cont.)
[S
t
op
Sele
ct]
Parameter # 10 Factory Default ‘‘Ramp”
[S
t
op
Sele
ct]
Parameter Type Read & Write
This parameter selects the stopping mode when the drive
re
c
e
i
ves
a
v
ali
d
s
to
p
comman
d
.
Units None Settings ‘‘Coast”
Causes the Drive to Turn Off
Immediately
re
c
e
i
ves
a
v
ali
d
s
to
p
comman
d
.
‘‘Ramp” Drive Decelerates to 0 Hz, Then Turns
Off – Requires a Value In
[Decel Time 1] or [Decel Time 2]
‘‘DC Brake”
Injects DC Braking Voltage Into the
Motor – Requires a Value in Both
[Decel Hold Time] & [Decel Hold
Level].
‘‘S-Curve”
Drive ramps to stop using ‘fixed S-Curve’
profile. Stop time is twice the selected
decel time.
[
Cu
rren
t
L
imit]
Parameter # 36 Factory Default 150 % of Drive Rated Current ➀
[
Cu
rren
t
L
imit]
Parameter Type Read & Write Minimum 20 % of Drive Rated Current ➀
This parameter sets the maximum drive output current that
is allowed before current limiting occurs. IMPORTANT: If a
value is programmed into the [Sec Curr Limit] parameter
then that value will be the active current limit value at
speeds above 1.5 times [Base Frequency]. See Fig. 5.5.
[Output 1 Config] and [Output 2 Config] can be set to
‘‘alarm” to indicate an overload condition exists.
Units 1 % Maximum 150% of Drive Rated Current ➀
IMPORTANT: See [Cur Lim Trip En] on page 5-35.
➀ The Drive Rated Ouput Current is based on three phase input ratings. See page 5-13 for instructions for Single Phase Input Ratings.
- User Manual 1
- Important User Information 2
- Document Update 3
- Summary of Changes 5
- Chapter 4 – Start-Up 8
- Chapter 5 – Programming 8
- Appendix C – Accessories 9
- Table of Contents 10
- Information and Precautions 11
- GENERAL PRECAUTIONS 12
- NAMEPLATE LOCATION 14
- FIRMWARE COMPATIBILITY 14
- Output ➀➁ 16
- Current (A) 16
- Installation/Wiring 17
- TERMINAL BLOCK ACCESS 19
- INPUT DEVICES 21
- INPUT POWER CONDITIONING 22
- INPUT FUSING 22
- RFI FILTERING 24
- GROUNDING 25
- POWER WIRING 27
- DRIVE OPERATION WITHOUT A 31
- HUMAN INTERFACE MODULE (HIM) 31
- CONTROL WIRING 31
- See notes on page 2-18 33
- OUTPUT DEVICES 35
- CABLE TERMINATION 35
- ADAPTERS 36
- Human Interface Module 39
- HIM REMOVAL AND INSTALLATION 42
- HIM MODES 43
- PROGRAM AND DISPLAY MODES 45
- Logic Mask 46
- X1111111 46
- Choose Group 46
- PROCESS MODE 47
- EEPROM MODE 48
- EEPROM MODE (cont.) 49
- SEARCH MODE 51
- CONTROL STATUS MODE 52
- CONTROL STATUS MODE (cont.) 53
- PASSWORD MODE 54
- PASSWORD MODE (cont.) 55
- Start-Up 59
- Chapter 4 –Start–Up 60
- DESCRIPTION 60
- HIM DISPLAY 60
- Reset Factory Defaults 61
- [Input Mode] Selection 61
- Open Enable Signal 64
- Restore Enable Signal 64
- Remove ALL Power 66
- Reconnect Motor 66
- Slowly Increase Speed 68
- Programming 69
- PROGRAMMING EXAMPLE 72
- Metering 73
- Metering Group (cont.) 74
- Set Up Group (cont.) 77
- Advanced Setup 82
- Advanced Set Up Group (cont.) 83
- Frequency 91
- Frequency Set Group (cont.) 92
- “French” 99
- “Italian” 99
- “Japanese” 99
- “Spanish” 99
- “German” 99
- Feature Select Group (cont.) 100
- 0 to [Maximum Freq] 102
- 815V/460V Drives 102
- Chapter 5 –Programming 103
- Cycling Input Power 104
- Diagnostics Group (cont.) 106
- Saves parameter Ram to EEPROM 109
- Masks Group (cont.) 111
- Controlling 114
- Not Controlling 114
- Owners Group (cont.) 115
- Adapter I/O 117
- Adapter I/O Group (cont.) 118
- Process Display 119
- Linear List 120
- CHAPTER OBJECTIVES 121
- FAULT INFORMATION 121
- Table 6.C Troubleshooting 129
- Appendix A – 133
- Appendix B – 139
- Appendix C – 155
Relacionado con productos y manuales para Equipo Rockwell-automation 1305 AC Drive, Firmware 1.01-3.00 User Manual
Equipo Rockwell-automation 1502 400 Amp Medium Voltage Contactor (Series D) Manual de usuario
(54 paginas)
(54 paginas)
Equipo Rockwell-automation 1494C-xxx Cable Operated 30A / 60A / 100A Disconne Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 1794-PS13_PS3 FLEX I/O dc Power Supply Install. In Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 1787-DNPS DeviceNet Power Supply Installation Inst Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation Logix5000 Program Parameters Programming Manual Manual de usuario
(36 paginas)
(36 paginas)
Equipo Rockwell-automation 1732D-XXXX PointBlock 16 dc Input Module Installat Manual de usuario
(24 paginas)
(24 paginas)
Equipo Rockwell-automation 1771-CFM Config. Flowmeter Installation Instructio Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O Manual de usuario
(120 paginas)
(120 paginas)
Equipo Rockwell-automation 1769-OA8 Compact 100 to 240V ac Solid State Output Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1734-PDN/B Point I/O DeviceNet Communication Inter Manual de usuario
(20 paginas)
(20 paginas)
Equipo Rockwell-automation 1786-RPFRXL ControlNet Fiber Ring Modules Installa Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 1732E-XXXX ArmorBlock 2-Port EtherNet/IP Modules w Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.143 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales