Rockwell-automation 21G PowerFlex 750-Series AC Drives Programming Man Manual de usuario Pagina 209
- Pagina / 544
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockwell Automation Publication 750-PM001J-EN-P - October 2014 209
Drive Port 0 Parameters Chapter 3
APPLICATIONS
Id Compensation
1604 IdCompMtrng 2 Iq
Id Compensation Motoring 2 Iq
Sets Iq value (in p.u.) at which P1603 [Id Comp Mtrng 2] (in p.u.) is specified.
This parameter is active only in motor control mode flux vector induction (P35 [Motor
Ctrl Mode] = 3 “Induction FV”).
Default:
Min/Max:
0.5000
0.0000 / 5.0000
RW Real
1605 Id Comp Mtrng 3
Id Compensation Motoring 3
Sets Id compensation value (in p.u.) at Iq = P1606 [IdCompMtrng 3 Iq] (in p.u.) for
motoring operation. Id compensation = Id Comp Mtrng 2 + (Id Comp Mtrng 3 – Id
Comp Mtrng 2) x (IqCmd – IdCompMtrng 2 Iq) x 1/(IdCompMtrng 3 Iq – IdCompMtrng 2
Iq) for IqCmd = between IdCompMtrng 2 Iq and IdCompMtrng 3 Iq. 1.0 p.u. is scaled to
the motor rated current.
This parameter is active only in motor control mode flux vector induction (P35 [Motor
Ctrl Mode] = 3 “Induction FV”).
Default:
Min/Max:
0.0000
–/+1.0000
RW Real
1606 IdCompMtrng 3 Iq
Id Compensation Motoring 3 Iq
Sets Iq value (in p.u.) at which P1605 [Id Comp Mtrng 3] (in p.u.) is specified.
This parameter is active only in motor control mode flux vector induction (P35 [Motor
Ctrl Mode] = 3 “Induction FV”).
Default:
Min/Max:
0.7500
0.0000 / 5.0000
RW Real
1607 Id Comp Mtrng 4
Id Compensation Motoring 4
Sets Id compensation value (in p.u.) at Iq = P1608 [IdCompMtrng 4 Iq] (in p.u.) for
motoring operation. Id compensation = Id Comp Mtrng 3 + (Id Comp Mtrng 4 – Id
Comp Mtrng 3) x (IqCmd – IdCompMtrng 3 Iq) x 1/(IdCompMtrng 4 Iq – IdCompMtrng 3
Iq) for IqCmd = between IdCompMtrng 3 Iq and IdCompMtrng 4 Iq. 1.0 p.u. is scaled to
the motor rated current.
This parameter is active only in motor control mode flux vector induction (P35 [Motor
Ctrl Mode] = 3 “Induction FV”).
Default:
Min/Max:
0.0000
–/+1.0000
RW Real
1608 IdCompMtrng 4 Iq
Id Compensation Motoring 4 Iq
Sets Iq value (in p.u.) at which P1607 [Id Comp Mtrng 4] (in p.u.) is specified.
This parameter is active only in motor control mode flux vector induction (P35 [Motor
Ctrl Mode] = 3 “Induction FV”).
Default:
Min/Max:
1.0000
0.0000 / 5.0000
RW Real
1609 Id Comp Mtrng 5
Id Compensation Motoring 5
Sets Id compensation value (in p.u.) at Iq = P1610 [IdCompMtrng 5 Iq] (in p.u.) for
motoring operation. Id compensation = Id Comp Mtrng 4 + (Id Comp Mtrng 5 – Id
Comp Mtrng 4) x (IqCmd – IdCompMtrng 4 Iq) x 1/(IdCompMtrng 5 Iq – IdCompMtrng 4
Iq) for IqCmd = between IdCompMtrng 4 Iq and IdCompMtrng 5 Iq. 1.0 p.u. is scaled to
the motor rated current.
This parameter is active only in motor control mode flux vector induction (P35 [Motor
Ctrl Mode] = 3 “Induction FV”).
Default:
Min/Max:
0.0000
–/+1.0000
RW Real
1610 IdCompMtrng 5 Iq
Id Compensation Motoring 5 Iq
Sets Iq value (in p.u.) at which P1609 [Id Comp Mtrng 5] (in p.u.) is specified.
This parameter is active only in motor control mode flux vector induction (P35 [Motor
Ctrl Mode] = 3 “Induction FV”).
Default:
Min/Max:
1.2500
0.0000 / 5.0000
RW Real
File
Group
No. Display Name
Full Name
Description
Values
Read-Write
Data Type
755
755
755
755
755
755
755
- Programming Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated Information 3
- Table of Contents 5
- Chapter 5 6
- Embedded Feature and Option 6
- Chapter 6 6
- Overview 9
- Obtaining Manuals 10
- Product Certification 11
- Manual Conventions 11
- General Precautions 12
- Product Safety 13
- Class 1 LED Product 13
- Start Up 15
- Figure 1 - DPI Ports ➊ and ➋ 16
- Start-Up Menu 17
- Drive Status Indicators 18
- EtherNet/IP 19
- Parameter Organization 21
- About Parameters 22
- Parameter Access Level 23
- How Drive Parameters are 24
- Organized 24
- Motor Control 26
- Feedback and IO 26
- Drive Cong 27
- Protection 27
- Speed Control 28
- Torque Control 28
- Psn Offset 1 Sel 820 29
- Diagnostics 30
- Applications 30
- Not Applicable 39
- Inverter Common (Port 10) 40
- Inverter Common 40
- Inverter n 40
- Converter Common (Port 11) 41
- Converter Common 41
- Converter n 41
- Precharge Common (Port 11) 42
- Precharge Common 42
- Precharge n 42
- Embedded EtherNet/IP 43
- Embedded DeviceLogix 44
- How Option Module 45
- Parameters are Organized 45
- 22-Series I/O Modules 46
- 22-Series I/O 46
- Single Incremental 47
- Dual Incremental 47
- Universal Feedback 48
- Safe Speed Monitor 49
- Drive Port 0 Parameters 51
- Drive (Port 0) Monitor File 52
- Drive (Port 0) Motor Control 54
- Frequency 55
- Drive (Port 0) Cfg File 84
- (1) Frames 1…7 only 92
- 755 (8+) 105
- Drive (Port 0) Speed Control 111
- Freq (Hz) 127
- Attenuation 127
- Drive (Port 0) Position 133
- Control File 133
- (1) 755 drives only 134
- Drive (Port 0) 148
- Communication File 148
- (2) 753 drives only 159
- (1) 753 drives only 160
- (3) 755 drives only 166
- (2) 755 drives only 167
- Drive (Port 0) Applications 172
- PI Error 174
- Alt Slope 196
- -axis offset is enabled 200
- Spindle Orientation Offset 207
- Drive (Port 0) General 212
- Purpose Parameters 212
- Chapter 4 215
- Inverter (Port 10) Common 216
- Parameters 216
- Inverter n (Port 10) 218
- Converter (Port 11) Common 221
- Converter n (Port 11) 223
- Precharge (Port 11) Common 227
- Precharge n (Port 11) 229
- Embedded EtherNet/IP (Port 234
- 13) Parameters 234
- Communication 240
- Configurations 240
- Table 4 - Logic Command Word 241
- Table 5 - Logic Status Word 242
- Embedded DeviceLogix (Port 243
- 14) Parameters 243
- 11-Series I/O Module 246
- 22-Series I/O Module 256
- Single Incremental Encoder 267
- Module Parameters 267
- Dual Incremental Encoder 269
- Universal Feedback Module 274
- Encoder Output Z Offset 286
- Registration Latch 0 290
- Registration Latch N 290
- Option Bus I/O 290
- Safe Speed Monitor Module 292
- Troubleshooting 305
- Faults, Alarms and 306
- Configurable Conditions 306
- HIM Indication 309
- Manually Clearing Faults 309
- Power Layer Interface (PLI) 310
- Board 7-Segment Display 310
- System Resource Allocation 311
- Chapter 6 Troubleshooting 312
- Drive Fault and Alarm 313
- Descriptions 313
- IMPORTANT 324
- for descriptions 324
- 194 Port12 Checksum 272 326
- Alarms (Frame 8 and Larger) 328
- I2 Curr Offset 331
- Converter (Port 11) Faults 333
- Precharge (Port 11) Faults 338
- N-1 and Re-Rate Functions 341
- Use the Re-Rate Feature 342
- Troubleshooting Chapter 6 343
- 13) Events 345
- Safe Torque Off Fault 347
- I/O Faults and Alarms 347
- ATEX Faults 348
- Faults and Alarms 348
- Universal Feedback Faults 350
- Port Verification 357
- Common Symptoms and 357
- Corrective Actions 357
- Motor operation is unstable 358
- Problems adding a datalink 359
- PowerFlex 755 Lifting/ 360
- Torque Proving 360
- External Brake Resistor 360
- Technical Support Options 361
- Technical Support Wizards 362
- Appendix A 363
- Block Diagrams 363
- * Notes, Important: 364
- PowerFlex 753 365
- VF (V/Hz), SV Overview 366
- Speed/Posit Fdbk 367
- Speed Control – Reference (1) 369
- Speed Control – Reference (2) 370
- Speed Control – Reference (3) 371
- Flux Vector 371
- Speed Control – Reference (4) 372
- VF (V/Hz), SV 372
- Speed Control – Reference (5) 373
- Speed Control – Regulator 374
- Position Control – Reference 375
- Position Control – Regulator 376
- In Position Detect 377
- Position Control – Homing 378
- Torque Control – Overview 379
- Induction Motor (IM) 379
- Torque Control – Torque 382
- Torque Control – Current 383
- Process Control (1) 385
- Process Control (2) 386
- MOP Control 387
- Dig In Filt 388
- Buffer & 394
- Comparator 394
- PF753 Rev_10.a 394
- Control Logic 395
- Inverter Overload IT 396
- PowerFlex 755 400
- Position Watch 1 412
- Position Watch 2 412
- Reref Psn In 414
- Speed/Position 415
- Move Table 415
- Roll Psn Config 417
- SO Offset 418
- Position 419
- Induction Motor (IM) & 420
- Total Inertia 426
- PF755 Rev_10.a 435
- Friction Compensation 438
- Peak Detect 440
- Digital Switches 440
- Diagnostic Tools 440
- High Speed Trend Wizard 441
- Application Notes 443
- Application Notes Appendix B 445
- Crane Setup with Encoder 446
- Feedback 446
- Set Up the Drive 447
- Motor Tune Routines 447
- Static Tune 448
- Rotate Tune 449
- Inertia Tune 450
- Torque Prove 452
- Setup Complete 453
- Crane Setup - Encoderless 455
- 6. Set speed reference 460
- 8. Set speed loop tuning 460
- Pump Off Function 463
- Gather Motor and Pump Data 464
- Enter Motor Data 464
- Run Motor Tune Routine 465
- Enter Pump Data 466
- Store Pump Cycle Torque 467
- Appendix B Application Notes 468
- Fine Tuning 469
- Sleep Mode 469
- Pump Off Control Outlines 470
- Table 2 - Parameter List 474
- Predictive Maintenance with 475
- Example Code 477
- Using DeviceLogix 483
- Function Block Elements 485
- Bit and Analog I/O Points 486
- Analog Inputs 487
- Analog Outputs 487
- Data Types 488
- Using DeviceLogix Appendix C 489
- Drive Datalink Value 489
- Program Examples 490
- Parameter Configuration 491
- Functional Block Programming 492
- Example 3: Diverter Operation 495
- Example 4: Wet Well Operation 496
- Example logic requirements: 499
- Permanent Magnet Motors 501
- Appendix E 505
- Introduction 505
- Feedback Configuration 507
- Parameter / Instance 512
- Attribute Mapping 512
- 431 1AF Position Trim 514
- Motor Overload 515
- Enhanced Attributes 516
- Additional Resources 525
- Rockwell Automation Support 544
- Documentation Feedback 544
Relacionado con productos y manuales para Equipo Rockwell-automation 21G PowerFlex 750-Series AC Drives Programming Man
Equipo Rockwell-automation 592-EEKF_EEMG E1 Plus Overload Relay Application a Manual de usuario
(4 paginas)
(4 paginas)
Equipo Rockwell-automation 150-SM3_SM4 SMC-50 Soft Starter I/O Option Module Manual de usuario
(4 paginas)
(4 paginas)
(2 paginas)
Equipo Rockwell-automation 284D- ArmorStart Base and Control Module Replaceme Manual de usuario
(2 paginas)
(2 paginas)
Equipo Rockwell-automation 20-750-PNET Profinet Single Port Option Module Manual de usuario
(96 paginas)
(96 paginas)
Equipo Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module Manual de usuario
(144 paginas)
(144 paginas)
Equipo Rockwell-automation 445L GuardShield Safe 4 and Safe 4 PAC Safety Ligh Manual de usuario
(40 paginas)
(40 paginas)
Equipo Rockwell-automation 160 Supplement-160-NX3 Chassis Mount Series C Manual de usuario
(12 paginas)
(12 paginas)
Equipo Rockwell-automation 140U Q, M frame CB Electronic RMS Trip Unit instal Manual de usuario
(14 paginas)
(14 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales