Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario descargar pdf (Pagina 31)

100

101

Chapter 2

Operating the Control

2-11

The 9/Series control offers a software MTB panel that performs many of

the functions of an MTB panel. This feature uses softkeys instead of the

normal switches and buttons of a panel. If your control uses a standard

MTB panel (described on page 2-8) or some other custom MTB panel,

the requests for operations from the panel take priority. This means that

requests from the software MTB panel are ignored if a request from a

standard or custom MTB panel is sent.

The software MTB panel’s operation depends on PAL, especially if the

control uses either a standard or custom MTB panel. See the

documentation prepared by your system installerfor details about using the

software MTB panel. Your system installer uses PAL to disable the

{FRONT PANEL} softkey.

The software MTB panel controls these features:

Feature Function

ModeSelect SelectseitherAUTO , MDI,or MANUALmodesasthe currentoperatingmode of thecontrol.

Rapid Traverse Replaces thefeedrate when executinga continuousjogmove withthe rapid feedrate.

FeedrateOverride Selects a feedrateoverride percentage forthe feedrate programmedwithan F word in any of thefeedratesmodes

(G93/G94/G95)and the reciprocationfeedrate programmedwith an Eword. This switchhas a range of0% to

150% ofthe programmedfeedrateand alterstheprogrammedfeedratei n 10% increments. When setto 0%,the

control iseffectivelyin feedhold.

Rapid FeedrateOverride Selectstheoverrideforrapidfeedrates. SelectfromF1,25%, 50%, and 100%,where F1 i s a rapid feedrate

override setting established in AMP by your system installer.

SpindleDirection Selects spindle rotation,clockwise(CW),spindle stop (OFF),orcounterclockwise(CCW). The frontpanel is

overriddenby any programmed spindledirection command.

SpindleSpeedOverride Selectstheoverride forprogrammedspindle speeds in 5%incrementswithin a rangeof50% to 120%.

DryRun Mode Placescontrolindryrun mode. T his replacesfeedrateswith thedry run feedrates. See page 7-21fordetails.

BlockDelete Allows activationof theblockdelete feature“/or /1”. Blockdelete 2 -9arenot available withthe

{FRONT PANEL}. See page 7-2 fordetails.

M-Function Lock AllowsselectM-,S-,T-, and B-codestobeignored. Seepage7-2fordetails.

Optional Stop Enablesor disables theM01 optional stopcode. When thisfeatureis“ON,” an M01inapartprogramstops

automatic execution. When thisfeatureis “OFF,”anM01in a part programis ignored. See page 10-31 fordetails

on M01.

SingleBlock Causes thecontrol to executeor checkone block of a partprogramorMDI entryeach timeyou pressthe

<CYCLE START> buttonwhenthisfeature ison.

WARNING:Singleblock execution isnotpossible duringreciprocation.

Mirror Image Mirrorstheaxis commandsin thepartprogramaround the selected axis. Seepage12-79for details.

AxisInhibit Preventsaxiscommandsfrombeingexecuted. The controlsimulates axismoti on on inhibited axesusingAcc/Dec

and feedrates; however,no actualaxismotion forthe inhibitedaxes is generated. Seepage7-20for details.

(continued on next page)

2.3

Software MTB Panel

{FRONT PANEL}

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 819 820

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra