Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario descargar pdf (Pagina 774)

Error and System Messages

Appendix B

B-20

Message Description

INVALID CHECKSUMDETECTED Thiserroris common forseveraldifferentsituations. Mosttypicallyit results when writingor

restoring invalid data toflash memory. For example ifaxis calibrationdata isbeingrestored to

flashand therewasan error or invalidmemory reference in theaxis calibrationdata file.

Typicallythis indicatesacorruptor invalidfile.

INVALID CNC F ILENAME An erroroccurred in G05 DH+ communications block.

INVALID CODE PROGRAMMEDFOR 7300 Aninvalid G or M code wasprogrammed during 7300 tapecompatibilitymode.

INVALID COMMUNICATIONS PARAMETER Parametersin G05 and/orG10.2communicationblocksareincorrect.

INVALID CO NTROL FOR DUALPROCESSSYS The system executivedownloaded tothe controldoesnotmatchthe hardware configuration

established by your optionchip.

INVALID CUTTER COMPENSATION NUMBER A compensationnumber (orTTRC number)out of therange of allowable compensation

numbers(eithertoo large or toosmall) wasprogrammed.

INVALID CYCLEPROFILE The path defining the cycle profile is not valid. This is typically caused by the cutter radius being

setto thewrongsign, being settoo large,or the valuesfor U,W,I,K,and the cutter radius

combinedare notvalidfor theprofile tobecut.

INVALID DATAAFTER A MACROCOMMAND Typicallycaused byanon-paramacro commandfollowing a paramacro command. Macroand

non-macro commandscannotexistin the sameblock.

INVALID DATABEFORE AMACRO COMMAND Typicallycausedby a non-paramacro command precedinga paramacrocommand. Macroand

non-macro commandscannotexistin the sameblock.

INVALID DA TA FORMAT MUST BE MM/DD/YY An invaliddateformatwas entered. The formatmustbe Month/ Day /Year(MM/DD/YY).

INVALID DEPTH PROBECONTROLLING AXIS Theaxisname which isAMPedasthe controllingaxis forthe depthaxis is notanaxisthathas

been configuredonthesystemor the adaptivedepthcontrolling axisis configuredasthe same

axisdefined tohavedepth probe feedback. Referto yourAMPreferencemanual fordetailson

axisconfiguration.

INVALID DESKEW MASTER T he AMPednamespecifyingthemasterdeskewservo isnotone of theAMPedaxes.

INVALID DESKEW SLAVE The AMPednamespecifyingthemasterdeskewservois notoneofthe AMPed axes,or ithas

alreadyselectedasa masteraxis.

INVALIDDHCOMMANDTYPE An error occurred i n G 05 DH+ communications block.

INVALID (DO) COMMANDNUMBER The specifiedloop number in a paramacro DO commandis outofthe legal range,ornot found.

DO commandsmustbe followed by a 1,2, or 3.

INVALID (END) COMMANDNUMBER A paramacroEND commandhas been encounteredwithout a matching DO orWHILE,or

outsidethe validrange. END commands mustbe followed by a 1,2,or 3,asprogrammedwith

thecorrespondingDO command.

INVALID ENDPOINT ING27 BLOCK The positionprogrammedin the G27 blockisnot thehomeposition. T he end-point ofa G27

blockmustbethemachinehomeposition.

INVALID EXPECTED LIFE The datajustenteredfortheexpected life ofthecuttingtool fortool managementis invalid.

INVALID EXPECTED TOOL LIFE The currentprogram isattemptingtoenter an invalidvaluefor thetool managementexpected

lifeof a tool. Tool lifei s programmedin a G10 block withan L-word.

INVALID F B COUNTS Atpower up thecontrol checkstheAMPconfiguredposition and velocityfeedbackcounts per

revoluti on. Ifeither ofthese parametersare invalid (forthishardware type)thiserror appears

and thecontrol isheldin E--Stop.

INVALID FDBK/MTR TYPE COMBO When changing between an executivefrom system9.xx to 10.xxsome major changes occurred

tohow a servo isconfiguratedin AMP. When copyingthisAMPprojectfrom 9.xxto 10.xxyou

mustopen and reconfigure someof theAMPservogroup parametersbeforesaving and

downloading tothe control.

INV ALID FILE TYPE Anerrorhas occurred in a filethathasbeensentfromthe ODSworkstation tothe control.

Typicallyitis theresultofODS sending thewrongfile typeto thecontrol(for example,an AMP

fileis sentwhenaPALdownload is takingplace,etc.). Attempttodownload the fileagain,

makingsure thatthe correctfile typeis selectedwhen downloaded.

1 2 ... 769 770 771 772 773 774 775 776 777 778 779 ... 819 820

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario Pagina 774

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra