Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario descargar pdf (Pagina 787)

Error and System Messages

Appendix B

B-33

Message Description

PALSOURCEREV. MISMATCH -- CAN’T MONITOR PALsource codeinthecontroldoesnot matchthe revisionof the CNC executive. The PAL

code mayexecuteifall ofthePALsystem flagsexist butthemonitorcannotbe used.

PAL USING MEMORY- REFORMAT The AMPparameter allowing PAL tobestored in RAM memory has been enabled. This

changesthe amountof RAMmemory available forpart programstorage,requiring theRAM disk

tobe reformatted. Partprogramsshould have been backeduppriorto this.

PARAMETER ASSIGNMENT SYNT AXERROR Ablockthatassigns Paramacro parametershas been enteredincorrectly.

PARAMETERNUMBER NOT FO UND TheAMPparameter numberbeingsearched forthroughthecontrol’s patchAMPutilitydoes not

exist in the system.

PARAMETERVALUEOUT OF RANGE The valueenteredfortheselectedAMPparameter or paramacroparameteris lessthanor

greaterthantheallowed legal value.

PARENTHESISINPUT ERROR Parentheseshavebeen entered incorrectlyin a programblockor calculationoperation. Correct

theuse of theparenthesis;verifytheyarein matchedpairs.

PARITYERROR IN PROGRAM Aserialcommunications errorhasoccurred. A dataparity erroroccurredwhilesendingor

receivingdata. T his can resultin a corruptedfile,orthe entiredate transferoperationmaybe

abortedby thecontrol.

PARK AXIS MOTION NOT ALLOWED Axismoti on was programmedfor a parkedaxis in a dual axis group. When both masterand

slaveaxes are parked,no axismotion isallowedonaparkedaxis in a dual group.

PART PROGRAMNOT SELECTED An attempt was madetoexecutea program orchecka programbefore a programwas selected

for execution.

PART ROTAT ION F ORMAT ERROR In partrotationblocks (G68,G69),only plane changesandmodechanges including inch/metric

and absolute/incrementalare permitted. Anycommandsother thannormal motioncommands

and themotion G-codes(G00, G01, G02, and G03) arenotpermitted.

PASSWORD PROTECTED When assigningpassword protectablefeaturesto an accesslevel,an attemptwasmade to

assigna featuretoa differentaccesslevelwhen the currentlyactivepassworddoesnot have

accesstothefeature. You can assignfeatures tootheraccesslevels only when youhave

accesstothatfeatureyourself.

PEAK CURRENT NOT 300% T h e axisfora 1394 or 9/440 is not AMPedtohave thePEAKCURRENT setto300%. T h is

misconfiguration forcesthecontroli nto E--Stop.

PERIPHERAL DEVICEERROR An illegal communication attemptwasmadewith a peripheral device,forexample,attemptingto

output

toa tape reader orinputfromatapepunch.

PLANE SELECT ERROR Anattemptwasmade to changeplanesduringcuttercompensation(TTRC), betweenQPP

blocks,orbetweenchamferandcornerrounding bl ocks. This error also will occur if G17 or G1 9

planesareselectedonalathe.

PLEASE WAIT FOR CLEARING OF PAL MEMORY PAL is being erasedin preparation fora PAL download.

PLUNGEMOTIONNOT ALLOWED The final plunge positionmustbe different fromthe startpointof the cycle. Thismessagecan

occurif theplungeaxisis notprogrammed in the entryblocktoG89 mode,orifthe plunge axis

incrementi s zero, or if thefinal plunge axisposition is thesameas the startpointof the cycle

blockduring G89 mode.

PLUNGEMOTIONNOT PROGRAMMED In yourpocketcycle you have eithernotprogrammed a finaldepth,or thefinal depth you have

programmedi s equal to the depthofthe cuttingtool atthestarting pointofthe cycle. The

location of the cutting tool when the pocket cycle is programmed mustbe at a diff erent depth

thanthefinal programmeddepthof the cycle.

PLUNGENOT ALLOWED Aplunge that will cutintothe pocket wall was requested in a G89 irregular pocket cycle.

PLUNGE STEPS MIS--PROGRAMMED The rough,medium,andfine-feed depths in the cycle b lock are notprogrammedcorrectly. This

ispossibleif thedatain the blockisincorrector if thedata in themodalvaluesof theparameter

notprogrammedintheblock areincorrect.

POCKET END NOT SAME AS ST ART A pocketend-pointthatis notthe sameasthe pocketstart-pointwas programmedin a G89

irregular pocket cycle.

1 2 ... 782 783 784 785 786 787 788 789 790 791 792 ... 819 820

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario Pagina 787

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra