Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario descargar pdf (Pagina 755)

100

101

Appendix

B-1

Error and System Messages

This appendix serves as a guide to error and system messages that can

occur during programming and operation of the 9/Series control. We listed

the messages in alphabetical order along with a brief description.

Important: To display both active and inactive messages, press the

{ERROR MESAGE} softkey found on softkey level 1. For details, see

chapter 2.

Important: This appendix covers only error and system messages.

PAL-generated operator messages generally appear on lines 21 and 22 of

the CRT and should be described in documentation prepared by the

machine tool builder.

Message Description

Symbols

(+) 15V SUPPLY FAILURE + 15 Vdcisnot available atthe main processor board. Checkthe wiresfromthemain power

supplyand connectorCN07 onthemain processorboard.

(--) 15V SUPPLY FAILURE -- 15 Vdc is notavailable at themain processorboard. Check the wiresfromthemain power

supplyand connectorCN07 onthemain processorboard.

(+) OVERTRAVEL PROGRAM ERROR Ifaxis motioncontinuesalongtheprogrammedpath,the indicatedaxis will reachorexceed the

positive software overtravel limit(runtime error).

(--) OVERTRAVEL PROGRAM ERROR Ifaxis motioncontinuesalongtheprogrammedpath,the indicatedaxiswill reach orexceedthe

negativesoftwareovertravel limit (runtime error).

(+) OVERTRVLPRGRAM ERROR: T he end-point ofthe commandedmove will causetheindicatedaxisto reachor exceed the

positive software overtravel limit (pre-execution error).

(--) OVERTRVL PRGRAM ERROR: The end-point ofthe commandedmove will causethe indicatedaxis to reachor exceed the

negativesoftware overtravel limit(pre-executionerror).

+/-- SIGN ERROR A + or -- sign was foundoutof placewhenanumericvalue wasbeingdecoded. Checkthe

active programblock forprogrammingformat errors.

1394 AXIS MODULE MISMAT CH At power turnon the systemidentified an axis module in the 1394 rack thatis misconfigured in

AMP. Ifanextra axis moduleispresentinthe1394 rackitshould eitherbe fully configured or

notconfiguredatall in AMPevenifthataxis module isnotused or detached.

1394 RINGCOMMUNICATIONSERROR Atpower up the internal communicationsring which runs throughthefrontofthe 1394 system

and drivemodules was eithernot connected,a device on theringexperienced a hardware

failure,oradeviceon the ring wasdiscoveredto be misconfigured once a commandwas sentto

thedevice. Makesure all axismodulesand the end terminator areproperlyconnectedto

complete the communicationring.

1746 RACKCARDS MISMAT CH The I/O configurationfor the1746I/O rack thatwas downloaded fromODS,orresidesin the

PALPROMs,contradictswhatis actuallyin therack(devicesmustmatchslot-for-slot).

1771 RACKCARDS MISMAT CH The I/O configurationfor the1771I/O rack thatwas downloaded fromODS,orresidesin the

PALPROMs,contradictswhatis actuallyin therack(devicesmustmatchslot-for-slot).

Overview

1 2 ... 750 751 752 753 754 755 756 757 758 759 760 ... 819 820

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario Pagina 755

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra