Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario descargar pdf (Pagina 761)

Error and System Messages

Appendix B

B-7

Message Description

CANNOT RENAME When performing a rename ofaprogramname,the new programname has notbeencorrectly

entered. The formatis OLD PROGRAMNAME,NEW PROGRAMNAME.

CANNOT REPLACE STAR TPOINT Anillegal attemptwasmade to changetheaxis calibrati on start-pointusing the online AMP

feature.

CANNOT RESTART G24 HARD STOP An attemptwas madetorestarta partprogram on a blockwhichwould have an axis atthe hard

stop. You cannotrestart ormidstarta partprogramafterif (atthatblocksexecution) any axis

would be holding againsta hard stop. You musteitherre-start/mid--startto a blockbefore the

G24 hard stopblock ortoa block afterthehard stopisreleased.

CANNOT SENDAVAILABLE COMMAND This is displayedwhen a non-programmedcommunications commandisexecutedfrom

“send’¨softkey.

CANNOT SET DA TA WHEN TOOL ISACTIVE Anattemptwas madeto manually(usingthe softkeys)change toolmanagement data forthe

currently activetool. Toolmanagementdata can be changedonlyfor a toolthatisnotcurrently

selected as the active tool.

CANNOT TAP INCSS YoumustdisabletheCSS feature before youbeginatappingoperation. Disable CSSusing a

G97 command.

CANNOT TAP INVIRTUAL-C MODE You attempted to use thesolid tappingfeature while cylindricalor end-facemilling was active.

CANNOT UPLOAD-PAL NOT INPROM PALcan be uploaded only fromthe PALPROMs. PAL in RAMmemorycannotbe uploaded.

CANNOT UPLOAD -PALSOURCE NOT LOADED When thesource isloaded,PAL canbeuploadedin the9/240 only . T he 9/260 and 9/290

alwayshave PAL in flash.

CANNOT USE COPY WITH ACTIVE TOOL OFFSET Anattempt wasmadeto copyoffsetdatafromone axistoanotherusingthe {COPYOFFSET}

softkey. You cannot usethissoftkeyif thetooloffsetsareactive.

CANNOT USEEXIT -BLOCKNO T FOUND An attemptwas madeto{EXIT}while searchingfora block fora mid-programstart. Youcannot

use{EXIT} until theblock has been found. To abortthe search,use {QUIT}.

CANNOT WRITEAREAD-ONLY P ARAMETER An attempt was made to assign a value to a P ALor system paramacro parameter that is a

read-onlyparameter. The value ofthese parameters can be usedonlybythe programmer;they

cannotbe alteredin theprogram.

CANNOT WRITE TOPROGRAM Thisindicatesaseriousproblemwiththe program. Attemptto writeto programa second time.

Ifretrydoesn’twork,you may havetodelete theprogram. Typically thiserror is notcaused by a

programmer or operatoraction,butratherby an internal programsoftware error.

CAUTION! YOU AREIN7300 TAPEMODE

TORETURNTOSTANDARD9/240 MODE

RESET THE 7300--COMPATIBILITY PAL FLAG

The operatoris cautionedthatthetape being copied ispresumed to be a 7300 formatted tape.

This message isdisplayedon the copy-tapeset-upscreen whentheMCU is in 7300

compatibility mode.

CC/TTRC ON,CAN’T ASSIGN TIME DEP. PARAM An attemptwas made toassign a time-dependentparamacro systemparameterwhile

dresser/wheelradiuscompensation was active. Time-dependantparametersare anysystem

parameters thatrecord orreferencea currentaxis position.

CHAMFERLENGT H/RADIUSTOO LARGE Achamferor radiusvalueprogrammedwith a ,Cor,R would generatea chamferor radius that

islargerthan one or bothof thetwoadjacenttoolpaths.

CHAMFER/RADIUS NOT ALLOWED Anattempt wasmadeto performa chamferorradius cut(programmedwith a ,Ror,C) in a

blockthatdoesnotallow thesefunctions tobeperformed. For example,you cannotdo a

chamfer or radiuscutin a non-motionblock,in the lastblockon an MDIline, or in thel ast block

ofa part program.

CHANGENOT MADEIN BUFFERED BLOCKS Changes to theoffsettable did notaffectthoseprogramblocksthatwerealready in thecontrol’s

currentactivationqueue. Programblocks thatcall foroffsetsand whichfollow thosealready in

theactivationqueue will call theupdatedoffset tables.

CHANNELNAMETOOLONG Thereisan error in G05 DH+ communicationsblock.

CHARMUSTBE _,.,LETTER,DIGIT Youhaveused incorrectsearchstringsyntax in the PALsearch monitorutility.

CHARMUSTBE LETTER,DIGIT, UNDERSCORE You have usedincorrectsearchstringsyntax in the PALsearch monitorutility.

CHARACTERSMUST BEDIGIT Youhaveused incorrectsearchstring syntax in the PALsearch monitorutility.

1 2 ... 756 757 758 759 760 761 762 763 764 765 766 ... 819 820

Comentarios a estos manuales

Sin comentarios

Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual de usuario Pagina 761

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra